Search:

Tag: 0.4

Search: Search took 0.00 seconds.

  1. Jointer tables - How flat do they need to be?

    Started by chocwheaton, 18th December 2013 12:41 PM
    5 Pages •
    1 2 3 4 5
    0.04, 0.1, 0.4, 2tsup, advice, approx, bed, cheers, comparison, deepest, dish, expensive, flat, gut, huge, in-feed, inch, jet, jointer, jpt-310hh, out-feed, planer/jointer, purchase, resolved, ruler, standard, table, tables, tool, wrong
    • Replies: 66
    • Views: 9,228
    Last Post: 25th February 2014 10:02 AM
    by mumbo  Go to last post

    Forum:
    GENERAL & SMALL MACHINERY

  2. Is this accurate enough for woodworking?

    Started by Arry, 13th January 2014 07:07 PM
    0.4, 25.90mm, 26.0mm, 26.10mm, 700mm, accurate, approximately, arry, assist, cheers, cut, dial, digital, fence, forward, guys, half, indicator, length, measurements, millimeter, opinion, piece, rip, setting, time, total, variance, width, woodworking 1 Attachment(s)
    • Replies: 13
    • Views: 2,346
    Last Post: 18th January 2014 03:15 PM
    by safari  Go to last post

    Forum:
    WOODWORK - GENERAL

  3. Weight of LVL's

    Started by Reno RSS Feed, 4th February 2013 02:10 AM
    0.063, 0.4, 400x63, 500, 550-650kg/m3, 75.6kg, close, density, lvls, net, read, renovateforum.com, searching, thread, weight
    • Replies: 0
    • Views: 1,112
    Last Post: 4th February 2013 02:10 AM
    by Reno RSS Feed  Go to last post

    Forum:
    STRUCTURAL RENOVATION, ROOFING, DEMOLITION, etc

  4. Two speed vice screw

    Started by Stustoys, 10th October 2011 09:47 PM
    0.1, 0.4, 1/2, brass, closing, continues, correct, forward, gear, hope, jaws, lol, makes, math, means, movable, moving, nut, pressure, rate, screw, sense, shaft, simple, speed, stops, stuart, thread, tighten, vice
    • Replies: 8
    • Views: 2,251
    Last Post: 11th October 2011 02:17 PM
    by Dave J  Go to last post

    Forum:
    METALWORK FORUM

  5. Thin Plywood

    Started by lakeside, 18th October 2009 11:30 AM
    0.4, 1.0, boat, bulls, charge, hobby, model, plywood, quantities, range, seeking, shops, supplier, thickness, thin, wounded
    • Replies: 10
    • Views: 6,870
    Last Post: 20th July 2011 05:47 PM
    by bobbee015  Go to last post

    Forum:
    BOAT BUILDING / REPAIRING

  6. Microclene MC1000

    Started by Groggy, 29th December 2008 05:48 PM
    3 Pages •
    1 2 3
    0.4, air, air filter system, blowing, box, carba-tec, clean, cleaning, cost, cubic, dust, dust extractor, filter, filters, fine, hour, manual, mc1000, microclene, micron, microns, particles, review, roof, run, tablesaw, time, unit, units, workshop
    • Replies: 38
    • Views: 15,837
    Last Post: 20th March 2011 04:22 PM
    by hughie  Go to last post

    Forum:
    PRODUCT REVIEWS

  7. Less smelly Glues for weight and veneer?

    Started by Joanna, 23rd June 2010 07:11 PM
    0.4, 47g, 500g, 57cm, animals, applications, carp, centimetres, chair, chemicals, couple, culled, depth, dimensions, dining, eat, glue, glueing, glues, guess, i.e, joanna, minced, smelly, square, surface, veneer, volatile, weight, wood
    • Replies: 5
    • Views: 1,790
    Last Post: 24th June 2010 12:29 PM
    by Woodwould  Go to last post

    Forum:
    GLUE

  8. irrregular holes in sheet metal

    Started by julianx, 11th March 2009 12:32 AM
    2 Pages •
    1 2
    0.4, advice, amount, appreciated, bit, considered, cut, dremel, fair, gauge, holes, irregular, irrregular, it;, job, lay, light, metal, moment, money, reasonable, sculptures, selection, shaped, sheet, skill, snips, stuck
    • Replies: 22
    • Views: 3,790
    Last Post: 15th March 2009 10:17 PM
    by julianx  Go to last post

    Forum:
    METALWORK FORUM

  9. Portable Edgebanders

    Started by zelk, 21st August 2008 11:18 AM
    2 Pages •
    1 2
    0.4, appreciated, brands, carbatec, comments, curious, edgebanders, edgebanding, edging, glued, ironing, jet, melamine, portable, pre, preglued, pvc, tired, virutex, zelk
    • Replies: 26
    • Views: 20,314
    Last Post: 1st October 2008 12:35 AM
    by zelk  Go to last post

    Forum:
    HAND TOOLS - POWERED

  10. A new pen tidy

    Started by jow104, 9th September 2008 07:28 PM
    0.4, american, ash, batch, black, box, clamps, copy, copying, friends, glued, handy, holding, including, lots, masking, offcut, offcuts, pen, pic, picture, relatives, section, started, successful, summer, tape, thickness, tidy, walnut
    • Replies: 9
    • Views: 2,192
    Last Post: 15th September 2008 09:58 PM
    by funkychicken  Go to last post

    Forum:
    BOX MAKING

  11. A first step on the slippery slope

    Started by Rocker, 22nd September 2005 07:35 PM
    2 Pages •
    1 2
    $10, $20, 0.4, 1/10, 3/8, cost, cut, dovetail, dovetails, earth, guide, hand, item, jarrah, jig, kerf, leigh, magnets, marker, methods, offcuts, rare, recently, rocker, set, slippery, slope, step, total, us$2
    • Replies: 16
    • Views: 3,284
    Last Post: 25th September 2005 05:47 PM
    by echnidna  Go to last post

    Forum:
    HOMEMADE TOOLS AND JIGS ETC.

Results 1 to 11 of 13