Search:

Tag: 90degrees

Search: Search took 0.00 seconds.

  1. First bench.

    Started by Tim_N, 2nd August 2014 04:34 PM
    321137, 321138, 321139, 90degrees, angles, bench, bottom, bowed, brush, camphor, caused, coat, dark, finished, forsner, funny, kinda, learnt, legs, lot, poly, project, seam, sit, sitting, straight, time, top, turps, ultra-clear 3 Attachment(s)
    • Replies: 3
    • Views: 2,225
    Last Post: 5th August 2014 11:43 PM
    by Christos  Go to last post

    Forum:
    WOODWORK PICS

  2. Another question on Incra Mitre 1000HD

    Started by Arron, 27th December 2012 09:02 PM
    1000hd, 45degrees, 90degrees, blade, chipping, close, cut, degrees, fence, hangs, incra, left, length, loosen, minimise, mitre, move, people, photo, post, proceed, protractor, question, reset, result, scale, screws, stop, till, time 2 Attachment(s)
    • Replies: 3
    • Views: 4,666
    Last Post: 28th December 2012 08:13 AM
    by Arron  Go to last post

    Forum:
    INCRA JIGS

  3. test indicator readings

    Started by eskimo, 28th May 2010 12:21 PM
    .000, .005mm, .01, .01mm, 90degrees, actual, angle, approximately, attached, contact, degrees, desk, diag, dial, direction, error, exact, found, head, indicator, junk, lower, measured, mitutoyo, reading, readings, setting, table, test, tram
    • Replies: 4
    • Views: 1,249
    Last Post: 30th May 2010 11:21 AM
    by eskimo  Go to last post

    Forum:
    METALWORK FORUM

  4. I never thought I was stupid but.................

    Started by SAISAY, 27th December 2009 04:54 PM
    90degrees, absolute/relative, angle, arabic, beat, blade, conversion, destructions, digital, english, explain, finder, mathematics, measurement, phd, plain, stupid, supposed, table, thought, understand, written, yy.yy%=tgax100%
    • Replies: 9
    • Views: 1,461
    Last Post: 29th December 2009 04:27 PM
    by SAISAY  Go to last post

    Forum:
    WOODWORK - GENERAL

  5. Dawn Wood Vice

    Started by Gunna do, 31st August 2009 08:04 PM
    $25, 90degrees, arrow, bench, dawn, days, decided, father, finished, gap, inlaw, level, machined, market, perfect, perfectly, pic, proper, screw, spent, spot, tapers, thomastown, time, vice, wood
    • Replies: 8
    • Views: 6,616
    Last Post: 4th September 2009 09:49 PM
    by Gunna do  Go to last post

    Forum:
    WOODWORK - GENERAL

  6. Outboard turning Dilemma

    Started by efgee88, 6th June 2009 12:31 PM
    90deg, 90degrees, alternative, banjo, bed, bold, bracket, dilemma, dvr, dvrxp, extension, head, lathe, maximum, mount, outboard, outrigger, owning, rest, rotated, section, setup, solid, spindle, stand, supported, tool, turning, vicmarc, vl175
    • Replies: 13
    • Views: 2,003
    Last Post: 12th June 2009 06:18 AM
    by rsser  Go to last post

    Forum:
    WOODTURNING - GENERAL

  7. Maximum veneer thickness

    Started by JB, 6th August 2006 06:37 PM
    120mm, 4mm, 90degrees, breaks, cracks/splits, cut, depends, glue, glued, maximum, occur, piece, ply/mdf/solid, proves, radial/quarter, strong, substrate, succesfully, suppose, tangenital/flat, thicker, thickness, veneer, wider, wood
    • Replies: 2
    • Views: 1,768
    Last Post: 8th August 2006 02:06 PM
    by Lumber Bunker  Go to last post

    Forum:
    TIMBER

  8. Cutting Mitres

    Started by WiZeR, 24th October 2005 06:42 PM
    90degrees, advice, apprecieated, bit, clean, cut, cutting, degree, edges, exposed, form, hide, left, managed, match, mitre, mitres, piece, ply, questions, remake, running, short, shorter, speed, square, thickness, tricky, triton, wood
    • Replies: 10
    • Views: 2,702
    Last Post: 25th October 2005 03:10 PM
    by TritonJapan  Go to last post

    Forum:
    TRITON / GMC

Results 1 to 8 of 8