Search:

Tag: countersink

Page 2 of 2 1 2

Search: Search took 0.01 seconds.

  1. Fettling a featherboard (c)

    Started by zenwood, 21st August 2005 12:11 AM
    backwards, bite, bolt, countersink, courtesy, device, featherboard, fence, fettling, filed, firmly, flats, head, hold, holds, ian007, idea, knob, prevents, proper, pushed, replace, screw, spinning, started, table, tighten, tightens, wingut, workpiece
    • Replies: 5
    • Views: 1,929
    Last Post: 21st August 2005 01:29 PM
    by echnidna  Go to last post

    Forum:
    HOMEMADE TOOLS AND JIGS ETC.

  2. Some more tools...

    Started by Schtoo, 8th August 2005 11:15 PM
    1/2, bit, blade, brass, bridge, buy, countersink, couple, drill, drilled, ferrule, filed, frame, hand, handle, hardware, hole, lathe, laying, makes, nice, obscene, rod, scraps, screw, strips, stuck, stuff, tools, widen
    • Replies: 4
    • Views: 1,892
    Last Post: 9th August 2005 12:46 PM
    by Schtoo  Go to last post

    Forum:
    HOMEMADE TOOLS AND JIGS ETC.

  3. Its all hanging on the hinge

    Started by PhilMcCrackin, 7th July 2005 03:41 PM
    5th, ab;le, advance, advice, bin, bit, bought, box, brass, concerned, countersink, flames, flat, gap, hanging, hinge, hinges, item, leaves, lid, local, minimise, mortise, nice, picture, shown, sits, unavoidable, visible, wife
    • Replies: 4
    • Views: 2,040
    Last Post: 7th July 2005 08:23 PM
    by gatiep  Go to last post

    Forum:
    WOODWORK - GENERAL

  4. Deck screws in hardwood

    Started by SBartleet, 30th June 2005 10:46 PM
    304, appreciated, beeswax, board, boards, chance, countersink, deck, drilling, gauge, hardwood, heard, hole, joist, joists, overkill, pilot, planning, properly, purchased, screw, screws, shear, stainless, steel, sufice, suggestions
    • Replies: 5
    • Views: 9,430
    Last Post: 2nd July 2005 12:28 PM
    by soundman  Go to last post

    Forum:
    DECKING

  5. Lee Valley stream has started to flow

    Started by BobR, 4th February 2005 08:53 PM
    again.d, bessy, bob, clamps, countersink, drill, flow, fore, gear, grade, gripper, june, k-body, lee, living, low-angle, mitre, month, osborne, plane, psa, sandpaper, ships, smooth, started, starts, stream, valley, veritas, woodworking
    • Replies: 4
    • Views: 1,631
    Last Post: 5th February 2005 03:38 PM
    by Kiwibrucee  Go to last post

    Forum:
    WOODWORK - GENERAL

  6. Speed control for induction motor

    Started by glenn k, 14th October 2004 12:05 AM
    2 Pages •
    1 2
    1/2, 180rpm, bit, blades, control, countersink, drill, easy, fast, holes, hot, induction, job, motor, press, proper, slow, slowest, speed, spring, steel, tungsten
    • Replies: 21
    • Views: 6,478
    Last Post: 25th October 2004 10:57 PM
    by forge  Go to last post

    Forum:
    HAND TOOLS - POWERED

  7. Making a Better Coping/Dovetail Saw

    Started by Bob Smalser, 5th October 2004 11:39 PM
    achieve, beech, bit, blade, brass, center, chuck, coping or dovetail, countersink, cutting, don’t, drill, drying, epoxy, ferrules, hand, handles, hardware, hole, holes, i’m, lathe, making, maple, mount, plumb, rod, saws, stock, tools
    • Replies: 7
    • Views: 5,390
    Last Post: 7th October 2004 12:38 PM
    by ryanarcher  Go to last post

    Forum:
    HAND TOOLS - UNPOWERED

  8. Dumb Countersinker

    Started by Termite, 20th July 2004 09:41 AM
    2 Pages •
    1 2
    bits, centre, change, chatter, chattering, countersink, countersinker, crap, dead, drill, dumb, free, helps, hey, hole, hope, industry, lazy, metal, non-lateral, perfect, presto, stupid, sunday, swearing, termite, thinkers
    • Replies: 22
    • Views: 4,873
    Last Post: 28th July 2004 11:06 PM
    by bsrlee  Go to last post

    Forum:
    WOODWORK - GENERAL

  9. sharpening things for mortice chisels

    Started by soundman, 9th June 2004 10:22 PM
    blades, bloke, chaps, cheer, chhisels, chisel, chisels, countersink, fashioned, gear, helpfull, middle, mortice, morticing, nice, overseas, plane, pride, real, repairs, sells, sharpening, sorts, speed, spigot, steel, things, thinking, wher, wonderfull
    • Replies: 1
    • Views: 1,987
    Last Post: 9th June 2004 10:27 PM
    by AlexS  Go to last post

    Forum:
    SHARPENING

  10. Countersink types

    Started by John G, 3rd April 2003 01:39 AM
    ages, ago, bit, blades, chatter, circular, completely, conical, countersink, countersinks, cutting, describe, design, edge, finish, hexagonal, hole, individual, lot, means, metalwork, post, previous, recommended, smooth, special, type, types, woodwork
    • Replies: 4
    • Views: 1,974
    Last Post: 3rd April 2003 11:56 PM
    by mikmaz1  Go to last post

    Forum:
    HAND TOOLS - POWERED

  11. Sizing considerations for wood screws:

    Started by RETIRED, 5th July 2001 03:28 PM
    considerations, countersink, day, depth, diameter, equal, hardwoods, hole, ian, joined, larger, length, max, pilot, robbo, robertson, rule-of-thumb, screw, screws, shopsmith, shorter, sizing, softwoods, strength, stronger, thread, tip, wood, woodworking, workpieces
    • Replies: 2
    • Views: 2,605
    Last Post: 10th July 2001 09:25 AM
    by Iain  Go to last post

    Forum:
    WOODWORK - GENERAL

Results 51 to 61 of 61
Page 2 of 2 1 2