Search:

Tag: donvale

Search: Search took 0.01 seconds.

  1. Donvale Casting and Stabilising Day

    Started by PenTurner, 8th December 2013 05:37 PM
    2 Pages •
    1 2
    296472, amos2tsup2tsup, attendees, bigshed, casting, dale, dallas, day, dessert, donvale, eat, fly, foreigner, fred, mark, neil, nothin, peter, post, qld, section, stabilising, start, started, sturdee, thread, treecycle, wall, yum, yum3 36 Attachment(s)
    • Replies: 25
    • Views: 3,393
    Last Post: 19th December 2013 04:27 PM
    by Sturdee  Go to last post

    Forum:
    WOODTURNING - PEN TURNING

  2. BBQ is ON - DONVALE IT IS

    Started by PenTurner, 28th November 2013 04:21 PM
    5 Pages •
    1 2 3 4 5
    043, addition, amos, bbq, behalf, cactus, cancel, casting, confirm, confusion, couple, demonstrate, demonstrating, donvale, electronics, ferntree, fit, gully, juice, mark, melton, mums, neil, offers, shop 8 Attachment(s)
    • Replies: 74
    • Views: 6,398
    Last Post: 8th December 2013 07:04 PM
    by DSEL74  Go to last post

    Forum:
    WOODTURNING - PEN TURNING

  3. VIC Festool OF 1400 Router used once

    Started by Greg Q, 12th September 2013 08:45 AM
    $750.00, 1400, ago, auction, break, buy, cost, donvale, festool, greg, note, option, photo, pick-up, post, prefer, projects, prolonged, purchased, quietly, router, sept, serious, sitting, systainer, version, woodworking
    • Replies: 1
    • Views: 1,427
    Last Post: 12th September 2013 05:14 PM
    by drnumbers  Go to last post

    Forum:
    Market Place/Auctions

  4. urgent help needed - sliding door snib lock

    Started by Reno RSS Feed, 21st October 2010 12:10 AM
    10am, advance, austyle, bunnings, direction, doncaster, donvale, door, doors, fit, latch, latching, lock, morning, orchards, park, pick, pool, reach, read, ready, renovateforum.com, reply, richard, ringwood, sliding, snib, thread, tomorrow, urgent
    • Replies: 0
    • Views: 1,802
    Last Post: 21st October 2010 12:10 AM
    by Reno RSS Feed  Go to last post

    Forum:
    DOORS, WINDOWS, ARCHITRAVES & SKIRTS ETC

  5. Mill way oil at cost. Donvale Melbourne

    Started by Greg Q, 6th August 2010 01:20 PM
    220, 361, bayswater, bearing, bought, confirm, cost, donvale, dorset, downstairs, edit, equivalent, filters, greg, guys, invoice, lathe, litres, melbourne, mill, mobil, oil, plain, sell, spindle, stuff, tonna, united, velocite, week
    • Replies: 2
    • Views: 1,751
    Last Post: 19th August 2010 10:03 PM
    by Travis Edwards  Go to last post

    Forum:
    METALWORK FORUM

  6. Slab Cutting

    Started by Mick4412, 17th July 2007 04:13 PM
    2300mm, 40mm, 500mm, 80mm, blue, consisitent, current, cut, cutting, dimensions, donvale, flat, gum, job, measurement, melbourne, mick, minus, offers, pay, prefer, professionally, slab, slabbed, slabs, suggestions, thick, thickness, timber, wide
    • Replies: 2
    • Views: 2,242
    Last Post: 17th July 2007 06:00 PM
    by Mick4412  Go to last post

    Forum:
    SMALL TIMBER MILLING

  7. 2 Phase Power ????

    Started by Mick4412, 25th October 2004 06:51 PM
    2 Pages •
    1 2
    agents, amp, bellarine, bigger, bit, donvale, drawing, dust, existing, extracter, folk, house, jointer, land, machines, mick, moving, peninsula, phase, possibility, power, selling, shed, single, suburban, table, terms, thicknesser, understand, wrong
    • Replies: 18
    • Views: 15,720
    Last Post: 10th July 2006 03:33 PM
    by TTIT  Go to last post

    Forum:
    HAND TOOLS - POWERED

  8. Tracks for Glass Sliding Doors

    Started by Mick4412, 8th November 2002 06:26 PM
    $50, 6mm, alternative, ball, bearings, bottom, channel, cheers, close, cowdreys, deep, donvale, doors, glass, metre, mick, nylon, prefer, quoted, rolls-royce, sliding, steel, sufficiently, supplier, top, tracks, up-market, version, versions, w-channel
    • Replies: 0
    • Views: 2,894
    Last Post: 8th November 2002 06:26 PM
    by Mick4412  Go to last post

    Forum:
    WOODWORK - GENERAL

  9. Sharpening Band Saw Blades

    Started by Mick4412, 6th September 2002 07:12 PM
    $18, $20, band, blackburn, blades, buying, carba-tec, close, compared, cost, date, donvale, gooing, melbourne, mick, re-sharpened, reasonable, recommendations, reliable, sharpening, suggestion, views
    • Replies: 7
    • Views: 3,443
    Last Post: 10th September 2002 01:22 AM
    by ubeaut  Go to last post

    Forum:
    BANDSAWS

Results 1 to 9 of 10