Search:

Tag: galling

Search: Search took 0.00 seconds.

  1. Has any seen a Kobalt 50mm chisel at Masters?

    Started by Grahame Collins, 8th March 2014 03:45 PM
    ,as, .the, 38mm, 50mm, advance, chisel, chisels, consultant, feedback, galling, grahame, home, improvement, information, kobalt, line, masters, online, results, section, send, software, staff, stock, store, stores.if, stuff, tells, trouble, wondering
    • Replies: 13
    • Views: 3,259
    Last Post: 1st April 2014 08:51 AM
    by Grahame Collins  Go to last post

    Forum:
    HAND TOOLS - UNPOWERED

  2. pallas horizontal rejuvenating

    Started by tanii51, 31st January 2014 09:31 AM
    axis, bed, bottom, bringing, call, clean, dramas, finished, fix, galling, horizontal, ignore, life, luckily, machine, marks, milling, oil, pallas, pics, rejuvenating, retainers 9 Attachment(s)
    • Replies: 12
    • Views: 1,927
    Last Post: 13th February 2014 01:50 PM
    by Steamwhisperer  Go to last post

    Forum:
    METALWORK FORUM

  3. Cheap bushing/bearing options for an 85mm shaft?

    Started by gallegos, 27th November 2013 08:13 PM
    $500, 85mm, bearing, bearings, bronze, bushes, bushing or bearing, cast, cheap, couple, foot, galling, hardened, hundred, iron, issue, local, lubricated, option, options, overseas, pretty, shaft, size, steel, stock, trouble, wear, welding, worried 2 Attachment(s)
    • Replies: 10
    • Views: 1,737
    Last Post: 29th November 2013 04:19 PM
    by gallegos  Go to last post

    Forum:
    METALWORK FORUM

  4. Chipmaster Thread Cutting

    Started by Piers037, 6th August 2013 11:03 PM
    2 Pages •
    1 2
    appears, carnage, centre, cheers, chipmaster, compound, crank, cross, cut, cutting, dial, disengage, engage, galling, half, hand, height, lash, missing, nut, piers, ripping, screw, set, slide, thou, thread, touch, treads, wind 7 Attachment(s)
    • Replies: 24
    • Views: 3,401
    Last Post: 10th August 2013 01:08 AM
    by j.ashburn  Go to last post

    Forum:
    METALWORK FORUM

  5. New stand for "Dolly" - ideas needed

    Started by richmond68, 30th November 2012 05:25 PM
    350, 3mm, 500, 700, accepted, angle, bit, bottom, box, cheat, copy, corner, desired, dolly, frame, galling, gratefully, ideas, motor, mount, needed, plate, posts, rhs, stand, tensioner, thinking, top, wood, woodworker
    • Replies: 2
    • Views: 1,704
    Last Post: 30th November 2012 10:07 PM
    by richmond68  Go to last post

    Forum:
    BANDSAWS

  6. "Y" Axis Rails

    Started by NedG, 23rd August 2012 10:00 PM
    aus, axis, built, cnc, fla, forums, galling, machine, rails, reckon, steel, thread, trouble
    • Replies: 3
    • Views: 1,363
    Last Post: 24th August 2012 09:26 PM
    by SawDustSniffer  Go to last post

    Forum:
    CNC Machines

  7. 3 machine failures in a week.

    Started by Grahame Collins, 9th April 2011 07:09 PM
    box, cutting, dollar, failures, galling, gear, grahame, grease, grease-, grinder, guy, hafco, jaw, kids, lines, lube, machine, manual, master, middle, oil, pretty, recess, relay, set, supports, switch, tech, vice, week
    • Replies: 2
    • Views: 1,117
    Last Post: 9th April 2011 08:26 PM
    by Dave J  Go to last post

    Forum:
    METALWORK FORUM

  8. Galling

    Started by Hawk, 24th December 2009 08:40 AM
    2 Pages •
    1 2
    annapolis, avoid, christmas, coat, dads, damaged, direction, easy, galling, grinder, lubricant, machined, merry, nut, pins, post, predicament, removal, rowing, season, seat, silly, sliding, stainless, steel, tale, thread, unable, wherry, worst
    • Replies: 25
    • Views: 4,290
    Last Post: 25th March 2010 08:26 PM
    by johmar  Go to last post

    Forum:
    MISC BOAT RELATED STUFF

  9. Fuel Failures

    Started by 741Baus, 24th March 2009 09:04 AM
    ,exhaust, 100247, 2-stroke, additives, build, certified, deposits, detergent, detergents, emission, engine, exhaust, failures, forming, fuel, galling, gases, grooves, gum, heavy, lacquer, octane, petrol, piston, premium, ring, start, sticking, stroke, surface, varnish
    • Replies: 0
    • Views: 1,479
    Last Post: 24th March 2009 09:04 AM
    by 741Baus  Go to last post

    Forum:
    SMALL TIMBER MILLING

  10. Hercus in the Canadian north

    Started by 12teethperinch, 3rd November 2008 04:19 AM
    ar11862v, barely, canadian, cramped, dryed, effort, expected, father, galling, gear, grease, hercus, inch, joined, lathe, ml7r, move, myford, nice, north, pristene, proud, recently, seased, serial, shaft, shape, shop, siblings, stiff
    • Replies: 9
    • Views: 2,268
    Last Post: 30th November 2008 05:16 PM
    by bitza500  Go to last post

    Forum:
    THE HERCUS AREA

Results 1 to 10 of 10