Search:

Tag: kink

Search: Search took 0.00 seconds.

  1. Kinked saw plate repair

    Started by kaf, 31st July 2014 01:15 AM
    2 Pages •
    1 2
    backsaw, bought, contacted, disappointment, ebay, entire, fancy, fix, hammer, kink, kinked, length, looked, plate, recently, repair, seller, user 2 Attachment(s)
    • Replies: 25
    • Views: 4,992
    Last Post: 12th August 2014 10:01 AM
    by planemaker  Go to last post

    Forum:
    HAND TOOLS - UNPOWERED

  2. Grrrrrrr!!!

    Started by artme, 3rd June 2014 09:53 PM
    allen, backwards, bewdy, blade, blank, blunt, bottom, couple, cut, cuts, decided, fiddled, fired, grrrrrrr, guide, guides, kink, looked, move, round, screw, set, setting, spun, teeth, test, thrust, top, twiddled, wheel
    • Replies: 8
    • Views: 2,269
    Last Post: 4th June 2014 04:01 PM
    by artme  Go to last post

    Forum:
    BANDSAWS

  3. Cheap holdown (the kind which wedges itself in a 3/4 dog hole)

    Started by jimhanna, 19th February 2014 01:09 AM
    3 or 4, bar, batten, bench, birdsmouth, bit, bolt, cheap, clamp, dog, drilled, found, head, holddown, holdfast, holdfasts, holding, holdown, hole, holes, it’s, kind, kink, planing, removed, stem, stock, unf, washer, wedges 7 Attachment(s)
    • Replies: 2
    • Views: 1,876
    Last Post: 20th February 2014 05:34 AM
    by jimhanna  Go to last post

    Forum:
    HOMEMADE TOOLS AND JIGS ETC.

  4. Hydraulic Pipe Bender

    Started by diz, 25th June 2011 08:59 PM
    2.5mm, 40mm, bend, bender, bends, cab, deg, dual, experience, formers, hydraulic, kink, metal, net, pipe, planning, read, round, steel, steps, support, tips, walls
    • Replies: 10
    • Views: 9,764
    Last Post: 4th July 2011 05:11 PM
    by Karl Robbers  Go to last post

    Forum:
    WELDING

  5. Finding the sewer pipes

    Started by Reno RSS Feed, 22nd November 2008 05:20 PM
    2nd, assuming, attached, connect, correct, deck, digging, hole, house, inspection, kink, line, main, parallel, passes, photo2, photos, pipe, pipes, questions, read, renovateforum.com, run, sewer, straight, string, stringline, telling, thread, thumbnails
    • Replies: 0
    • Views: 1,656
    Last Post: 22nd November 2008 05:20 PM
    by Reno RSS Feed  Go to last post

    Forum:
    PLUMBING, ELECTRICAL, HEATING, COOLING, etc

  6. The unusual turning of a chair leg.

    Started by Woodwould, 21st June 2008 01:19 PM
    accommodate, additional, bandsawn, block, chair, cum, glued, headstock, identified, kink, leg, lower, main, oak, off-set, original, partially, piece, plainly, portion, rail, readers, rear, replacement, seat, seventeenth, support, sweep, turning, unusual
    • Replies: 2
    • Views: 1,710
    Last Post: 22nd June 2008 11:18 AM
    by Woodwould  Go to last post

    Forum:
    WOODWORK - GENERAL

  7. Straightening lead screw

    Started by Fossil, 29th May 2008 06:10 PM
    2 Pages •
    1 2
    3/16, axe/hammer, biting, bullet, carriage, couple, cuts, deformed, feedthe, finally, finish, gas, intending, issues, kink, lathes, lead, lifts, power, screw, slightly, straighten, straightening, suggestions, surface
    • Replies: 17
    • Views: 3,843
    Last Post: 12th June 2008 09:39 AM
    by hux  Go to last post

    Forum:
    METALWORK FORUM

  8. Wonky band

    Started by Chumley, 14th April 2008 10:23 AM
    adam, angle, band, bandsaw, blockage, chance, checked, cheers, couple, cut, experience, feeding, job, kicks, kink, learning, mdf, pairs, passes, piece, pliers, real, regularly, smooth, straighten, trash, twist, twisting, wonky, yesterday
    • Replies: 3
    • Views: 1,869
    Last Post: 14th April 2008 12:01 PM
    by Chumley  Go to last post

    Forum:
    BANDSAWS

  9. Straightening Bent Handsaw Blades

    Started by Bob Smalser, 11th August 2007 02:52 PM
    anvil, bent, blade, blades, can’t, chalk, convex, cutting, dimple, edge, gullets, hammer, handsaw, i’ll, identical, kink, light, remove, removed, saw’s, sawblades, saws, slightly, steel, straightening, surface, taper, tension, tensioning, thin
    • Replies: 10
    • Views: 3,579
    Last Post: 16th August 2007 02:43 PM
    by Bob Smalser  Go to last post

    Forum:
    HAND TOOLS - UNPOWERED

  10. Twisted / Buckled blade

    Started by Sir Stinkalot, 6th August 2006 07:11 PM
    appears, bad, band, blade, boxes, buckled, cheers, continued, cut, cutting, definite, developed, drawers, force, front, improve, kink, knock, mad, mechanism, newish, pushed, stinky, stock, stupidity, surge, tension, time, twisted, wobble
    • Replies: 14
    • Views: 2,233
    Last Post: 8th August 2006 11:21 PM
    by echnidna  Go to last post

    Forum:
    BANDSAWS

  11. Straightening out a compass saw blade

    Started by Green Woodchips, 19th July 2005 08:52 PM
    affect, beech, bend, blade, bothering, brand, broken, cheers, compass, corrected, day, destroying, fine, fix, gday, gloat, handle, i.e, jackson, kink, minor, performance, post, previous, qus, slight, spear, straightening, stress, worth
    • Replies: 2
    • Views: 1,503
    Last Post: 20th July 2005 05:01 PM
    by Green Woodchips  Go to last post

    Forum:
    HAND TOOLS - UNPOWERED

Results 1 to 11 of 11