Search:

Tag: locates

Search: Search took 0.00 seconds.

  1. Machining tiny components

    Started by morrisman, 1st June 2013 09:02 PM
    1950s, 60s, body, brass, cheap, chuck, collar, collet, components, groove, ground, hack, hole, jaw, locates, loco, locos, machine, machining, mike, motor/bogie, original, size, stuff, tapped, thin, tiny, tool, trains, unit 3 Attachment(s)
    • Replies: 8
    • Views: 1,809
    Last Post: 3rd June 2013 08:39 AM
    by arose62  Go to last post

    Forum:
    METALWORK FORUM

  2. AL 1000D Lathe compound modification.

    Started by krisfarm, 15th June 2011 05:25 PM
    1000d, access, angle, anoying, bob, combination, compound, deceided, fitted, fix, hole, lathe, locates, looked, modification, nut, nuts, pictures, position, prevents, result, ring, round, spacer, spacers, stuck, them-, tighten, tightening, tilting
    • Replies: 4
    • Views: 3,519
    Last Post: 15th June 2011 10:25 PM
    by Dave J  Go to last post

    Forum:
    METALWORK FORUM

  3. Made up another jig I quite like.

    Started by JDarvall, 22nd March 2008 03:16 PM
    attached, bandsaw, block, centre, chopped, droop, fence, fine, finewoodworking, jig, kicked, locates, love, magazine, magizine, pinched, quick, quickly, real, runs, simple, slot, stock, strip, table, timber, wood, zip
    • Replies: 12
    • Views: 2,654
    Last Post: 24th March 2008 11:26 PM
    by JDarvall  Go to last post

    Forum:
    WOODTURNING - GENERAL

  4. turning alloy

    Started by robyn2839, 14th September 2007 10:58 PM
    ,bolted, ,marked, alloy, blank, bob, bowl, centre, centred, chuck, cost, cut, finished, flat, groove, hardest, left, lines, locates, locator, peice, ring, rubbery, simple, spot, timescrewed, tomorrow, turning, wooden
    • Replies: 8
    • Views: 1,778
    Last Post: 16th September 2007 09:20 AM
    by robyn2839  Go to last post

    Forum:
    WOODTURNING - GENERAL

  5. Milling attachment for lathe

    Started by graemet, 2nd July 2006 10:19 PM
    added, assembly, attachment, bolt, c/s, cheers, conditions, design, graeme, hand, head, held, lathe, locates, locked, loctite, milling, mounting, position, screw, screws, single, slide, socket, stop, suit, tension, threaded, vertical, vice
    • Replies: 3
    • Views: 6,145
    Last Post: 3rd July 2006 08:48 PM
    by graemet  Go to last post

    Forum:
    METALWORK FORUM

  6. so true

    Started by Gino, 25th October 2000 04:34 PM
    altitude, balloon, balloonist, correct, descends, discovers, distance, excuse, expect, fault, feet, field, ground, hearing, hopelessly, hot-air, information, locates, lost, lower, lowers, management, met, position, replies, technically, thirty, told, true, wandered
    • Replies: 0
    • Views: 1,132
    Last Post: 25th October 2000 04:34 PM
    by Gino  Go to last post

    Forum:
    WOODIES JOKES

Results 1 to 6 of 6