Search:

Tag: m/m

Search: Search took 0.00 seconds.

  1. VIC Here are some surplus tools I have, need the room and the money to buy some more tool

    Started by Fix it Fritz, 12th May 2014 09:39 PM
    $20.00, 155, adapter, bearing, bendigo, bit, bushings, buy, diameter, drill, fit, fitted, guide, happy, holes, kit, m/m, match, money, pick, plate, post, router, routers, surplus, tool, tools, trim, trimmed, victoria 1 Attachment(s)
    • Replies: 11
    • Views: 2,189
    Last Post: 16th May 2014 07:33 PM
    by KBs PensNmore  Go to last post

    Forum:
    Market Place/Auctions

  2. NSW Interested in swapping my Carbatec table saw for a makita MLT100

    Started by unicorn, 9th October 2013 01:54 PM
    1800, 288720, actual, aluminium, based, bay, blade, blade.it, byron, carbatec, cheers, couple, crosscut, m/m, makita, mlt100, motor, negative, phase, post, rake, remote, single, sliding, spare, switch, table, throw, volt 1 Attachment(s)
    • Replies: 1
    • Views: 2,187
    Last Post: 22nd October 2013 10:16 AM
    by xboa721  Go to last post

    Forum:
    Market Place/Auctions

  3. Planer blades alignment jig

    Started by Ricardo292, 31st August 2012 06:00 PM
    alignment, answer, blade, blades, cheap, feed, fence, happy, jig, length, level, m/m, magnet, magnets, mark, opposite, pass, pic, pics, pieces, planer, planner, plase, question, screws, secure, steel, stick, table, tube
    • Replies: 0
    • Views: 1,435
    Last Post: 31st August 2012 06:00 PM
    by Ricardo292  Go to last post

    Forum:
    HOMEMADE TOOLS AND JIGS ETC.

  4. Which glue to use

    Started by John Williams, 27th August 2012 01:09 PM
    ,cross, .what, 300, 70x50, bead, bearers, braced, clamps, drumming, floorcramps, force, gday, glue, grove, iam, m/m, metres, reakon, run, screw, sitting, squeeze, stop, thinking, type, vibrations, wide, wood.the
    • Replies: 2
    • Views: 1,847
    Last Post: 27th August 2012 03:02 PM
    by John Williams  Go to last post

    Forum:
    GLUE

  5. First (half decent) box

    Started by unicorn, 15th May 2010 01:05 PM
    boards, bottom, box, careful, contribution;, corner, cut, decent, generous, grain, half, handle, hinges, inserts, internal, m/m, mango, matching, myrtle, recycled, resawn, round, scroll.ill, tassie, thick, time, tip, upside, wardrobe, wooden
    • Replies: 9
    • Views: 1,661
    Last Post: 16th May 2010 08:43 PM
    by artme  Go to last post

    Forum:
    BOX MAKING

  6. GMC chainsaw HELP!!

    Started by unicorn, 30th June 2009 10:00 AM
    400, anti-kick, apartas, bsc1800, chainsaw, chainsaw;, deadgmc, diagram, disconnecting, drive, emergency, everyone;, gmc, line, m/m, model, prong, pulled, raul, runs, sprocket, stop
    • Replies: 0
    • Views: 1,458
    Last Post: 30th June 2009 10:00 AM
    by unicorn  Go to last post

    Forum:
    TRITON / GMC

  7. suggestions for repair

    Started by TeeDee, 12th March 2008 10:22 AM
    100, blade, cloth, cover, damaged, edges, epoxy, fibreglass, fill, glue, hacksaw, hole, inside, interface, m/m, managed, paint, past, pics, piece, ply, polyester, post, pushed, repair, straight, suggestions, surface, timber, torn
    • Replies: 3
    • Views: 1,320
    Last Post: 14th March 2008 08:39 AM
    by TeeDee  Go to last post

    Forum:
    BOAT BUILDING / REPAIRING

  8. Outboard turning on jet 1642

    Started by Grumpy John, 28th August 2006 06:20 PM
    1642, 500, advice, cheers, dia, gang, jet, m/m, outboard, outrigger, oversize, purchased, setup, turning, wondering
    • Replies: 2
    • Views: 2,095
    Last Post: 29th August 2006 10:21 AM
    by hughie  Go to last post

    Forum:
    WOODTURNING - GENERAL

Results 1 to 8 of 8