Search:

Tag: ont

Search: Search took 0.00 seconds.

  1. Recommended miller for Griffith NSW

    Started by Evanism, 4th February 2014 03:16 PM
    aparently, dramatically, drop/tractor, easy, family, griffith, heir, hint, internet, italian, law, leads, list, lucas, matter, milers, milled, miller, mins, nsw, ont, option, owner, recommended, required/requested, site, time, trailer, trees, uncle
    • Replies: 1
    • Views: 1,550
    Last Post: 4th February 2014 10:45 PM
    by Sigidi  Go to last post

    Forum:
    SMALL TIMBER MILLING

  2. Bench construction question

    Started by Philostine, 18th December 2010 08:14 AM
    10mm, 2400mm, 45x90mm, 90mm, bench, bowed, building, buiting, clamps, construction, dead, flat, gluing, hand, laminating, length, oak, ont, phil, pieces, plane, process, question, section, straight, straighten, tazzie, thick, tools, top
    • Replies: 7
    • Views: 1,678
    Last Post: 28th December 2010 02:26 PM
    by Philostine  Go to last post

    Forum:
    THE WORK BENCH

  3. Cordless drill batteries

    Started by SHEETMETAL, 31st December 2009 01:40 PM
    $165.00, $330.00, batteries, bosch, buy, cheap, cordless, drill, fellow, home, logged, ont, page, power, price, replace, source, suggestions, tools, woodworkers
    • Replies: 12
    • Views: 3,463
    Last Post: 14th January 2010 01:01 PM
    by LanceC  Go to last post

    Forum:
    HAND TOOLS - POWERED

  4. my outdoor setting desighn

    Started by weisyboy, 18th May 2009 08:13 PM
    desighn, gotta, ont, outdoor, rough, seats, setting, shaping, timber, woman
    • Replies: 0
    • Views: 904
    Last Post: 18th May 2009 08:13 PM
    by weisyboy  Go to last post

    Forum:
    WOODWORK - GENERAL

  5. triton router table.

    Started by jow104, 26th July 2007 06:49 PM
    2000workcentre, bit, distance, error, fence, forum, likewink, link, method, ont, pull, router, run, setting, system, table, timber, trial, triton
    • Replies: 3
    • Views: 1,421
    Last Post: 30th July 2007 10:20 PM
    by jow104  Go to last post

    Forum:
    TRITON / GMC

  6. Poor mans panel saw

    Started by Lignum, 10th March 2007 04:07 PM
    90deg, accurate, added, angles, beautifully, blocks, board, comfortably, cross, cut, easy, fence, handle, height, holding, length, makes, mans, ont, panel, parafon, ply, poor, seperate, sitting, slide, slip, supported, wax, workmate
    • Replies: 3
    • Views: 1,931
    Last Post: 11th March 2007 08:53 AM
    by Auld Bassoon  Go to last post

    Forum:
    WOODWORK - GENERAL

  7. Sanding back some high spots - Self levelling cement

    Started by powerbuff, 7th September 2006 05:36 PM
    3mm, abut, added, bag, build, cement, concrete, day, floating, floors, grinding, high, level, levelling, ont, poured, putting, quick, rest, sand, sanding, set, setting, short, slightly, spots, started
    • Replies: 1
    • Views: 2,973
    Last Post: 7th September 2006 05:49 PM
    by powerbuff  Go to last post

    Forum:
    CONCRETING

  8. lawn irrigation

    Started by Stu, 4th September 2005 05:02 PM
    19mm, advice, appreciated, budget, buffalo, cheap, cheers, experience, extend, grass, greatly, hense, instant, irrigation, lawn, lawn/weeds, lifter, ont, perth, pipe, planted, poly, putting, roller, runners, sir, soft, stu, walter, woudl
    • Replies: 12
    • Views: 3,475
    Last Post: 3rd October 2005 09:44 PM
    by Stu  Go to last post

    Forum:
    LANDSCAPING, GARDENING, OUTDOORS

  9. Your opinion please.

    Started by Fred in Tassie, 18th April 2005 09:25 PM
    2 Pages •
    1 2
    alternatives, brings, carbatec, cheaper, cheers, direct, financial, forums, fred, ideal, lathe, lathe-9890.aspx, mc900, msl-3815, note, ont, opinion, preservation, purchase, question, replace, replacement, sold, stretch, thread, timbecon, time, transfered, vicmarc, wellbeing
    • Replies: 15
    • Views: 3,281
    Last Post: 20th April 2005 06:01 PM
    by graemecarson  Go to last post

    Forum:
    WOODTURNING - GENERAL

  10. High Fence for WC

    Started by Mark Lyon, 28th September 2004 07:35 PM
    aluminium, attach, centain, cheers, cuts, existing, fence, frnce, high, hope, knowledgeable, method, ont, people, question, quick, sense, workcentre
    • Replies: 8
    • Views: 2,531
    Last Post: 4th October 2004 11:28 PM
    by Ishin  Go to last post

    Forum:
    TRITON / GMC

Results 1 to 10 of 10