Search:

Tag: potentiometer

Search: Search took 0.00 seconds.

  1. Potentiometer Problems on EVS Vicmarc Lathe

    Started by Kidbee, 9th July 2015 05:45 PM
    evs, lathe, potentiometer, problems, vicmarc 3 Attachment(s)
    • Replies: 9
    • Views: 2,645
    Last Post: 26th March 2016 02:14 PM
    by TimberNut  Go to last post

    Forum:
    WOODTURNING - GENERAL

  2. Variable Lathe spindle speed control project for constant surface speed

    Started by jhovel, 10th June 2014 08:37 PM
    2 Pages •
    1 2
    cnc, constant, control, cutting, data, desired, experienced, geometry, inputs, lathe, maintain, material, motor, operation, operators, options, positional, potentiometer, project, radius, set, slide, speed, spindle, surface, thread, time, tool, variable, voltage
    • Replies: 27
    • Views: 4,839
    Last Post: 15th October 2014 08:34 AM
    by Toggy  Go to last post

    Forum:
    METALWORK FORUM

  3. Now, THAT is service

    Started by SAISAY, 2nd February 2013 02:47 PM
    2.2kw, 2tsup, appreciated, chinglish, covered, cutters, english, frustrations, inverter, lack, lots, manual, potentiometer, produced, redsail, series, service, video, xinfutai
    • Replies: 0
    • Views: 1,355
    Last Post: 2nd February 2013 02:47 PM
    by SAISAY  Go to last post

    Forum:
    CNC Machines

  4. 6040 CNC (800 Watt Spindle VFD Settings Problem)

    Started by ishtalk, 27th May 2012 02:01 PM
    .8kw, 24000rpm, 6040, 800, changed, cnc, collet/chuck, contacting, dealt, factory, fine, half, hindsight, model, potentiometer, press, problem, properly, read, reset, run, sadness, settings, sounds, spindle, spinning, time, tuned, vfd, watt
    • Replies: 5
    • Views: 5,161
    Last Post: 28th May 2012 04:39 PM
    by ishtalk  Go to last post

    Forum:
    CNC Machines

  5. Sophisticated cutting device for lost foam castings

    Started by Michael G, 20th April 2012 10:55 PM
    anti, beam, castings, chain, contact, current, cutting, device, electrical, foam, gravity, integrated, linear, lost, maintained, ni-chrome, post, potentiometer, power, precision, regulates, roof, screwed, secured, shown, sliding, sophisticated, system, transfer, wire
    • Replies: 10
    • Views: 1,742
    Last Post: 22nd April 2012 09:56 PM
    by Michael G  Go to last post

    Forum:
    METALWORK FORUM

  6. Variable speed motors

    Started by artme, 3rd December 2011 08:30 PM
    2 Pages •
    1 2
    1800, 240v, 600, affected, cmg, comparison, control, devices, effective, greatly, instance, makes, market, motor, motors, phase, potentiometer, range, rpm, single, speed, torque, unit, variable
    • Replies: 27
    • Views: 3,886
    Last Post: 9th December 2011 11:35 AM
    by NeilS  Go to last post

    Forum:
    WOODTURNING - GENERAL

  7. TIG foot control for Chinese welder

    Started by Pete F, 28th July 2011 08:46 AM
    2 Pages •
    1 2
    10k, aluminium, amount, bit, box, chinese, control, feel, fine, floor, foot, heal, heat, heats, outrageous, pete, postage, potentiometer, prefer, pretty, price, sitting, source, strange, suit, switch, tig, torch, type, welder
    • Replies: 16
    • Views: 8,088
    Last Post: 4th August 2011 03:36 PM
    by PDW  Go to last post

    Forum:
    WELDING

  8. Potentiometer taper

    Started by Stustoys, 22nd August 2010 03:27 PM
    10kohm, control, linear, log, mill, pot, potentiometer, speed, stuart, taper
    • Replies: 10
    • Views: 1,634
    Last Post: 23rd August 2010 11:03 AM
    by Graziano  Go to last post

    Forum:
    METALWORK FORUM

  9. VSD Remote Control Panel Questions

    Started by markjaffa, 6th April 2010 11:00 PM
    2 Pages •
    1 2
    al-960b, cloned, control, controls, finer, forward, input, inputs, installed, jog, leaning, momentary, overkill, panel, pot, potentiometer, pushbutton, questions, reason, remote, resolution, reverse, run/start, single, speed, stop, suggest, switch, ten, vsd
    • Replies: 28
    • Views: 9,319
    Last Post: 20th April 2010 05:15 PM
    by eskimo  Go to last post

    Forum:
    METALWORK FORUM

  10. Console the ModIO Method

    Started by rodm, 4th August 2009 10:49 PM
    2 Pages •
    1 2
    attached, bits, brains, commands, communicate, console, couple, easy, graphical, interface, lcd, led, lot, mach3, macropump, method, methods, modio, mpg, panel, peter, photo, plodding, potentiometer, resting, started, switches, time, understand, understanding
    • Replies: 29
    • Views: 7,002
    Last Post: 12th September 2009 01:17 PM
    by rodm  Go to last post

    Forum:
    CNC Machines

  11. Help needed ..Electrical

    Started by Paddy, 6th December 2008 09:35 AM
    ,the, 16mm, alpha, amplifiers, appreciated, broke, control, dia, electrical, garden, guys, info, internet, knowledge, locate, lot, luck, metal, music, needed, people, potentiometer, replacement, rotary, spec;, suitable, thread, volt, volume, wife
    • Replies: 13
    • Views: 2,661
    Last Post: 19th February 2009 11:01 PM
    by rogerbaker  Go to last post

    Forum:
    METALWORK FORUM

Results 1 to 11 of 11