Search:

Tag: simons

Search: Search took 0.00 seconds.

  1. So Where To Next, The Motor Rewinder?

    Started by Anorak Bob, 5th April 2014 08:29 PM
    10 Pages •
    1 2 3 4 5 6 7 8 9 10
    309404, alan, bob, c-47, capital, copper, cutter, dealt, dig, digging, grinder, housing, light, minus, motor, no.1, perth, postable, replace, rewinder, rewinders, rotor, simons, stuff, suggestions, sweetmans, tool, twine, unravel, wire 69 Attachment(s)
    • Replies: 140
    • Views: 12,806
    Last Post: 27th April 2014 04:02 PM
    by BobL  Go to last post

    Forum:
    METALWORK FORUM

  2. Out with the new and in with the old

    Started by Ueee, 18th January 2014 06:32 PM
    2 Pages •
    1 2
    16x10, 240v, act, apparently, bandsaw, bs5s, calwell, cheers, contacted, cost, cut, ebay, guessing, h225, hafco, haggling, happened, lathe, listings, metal, mill, mud, pig, pulled, rang, reason, seller, simons, size, takes 12 Attachment(s)
    • Replies: 23
    • Views: 3,589
    Last Post: 28th January 2014 12:36 PM
    by simonl  Go to last post

    Forum:
    METALWORK FORUM

  3. A treasure from Bob

    Started by Michael G, 30th June 2013 09:57 PM
    bandsaw, bob, book, cam, change, copy, cut, cutters, dividing, do-hicky, gear, gears, head, lead, leadscrew, mentioned, mill, milling, operated, pair, pencil, rack, ran, recently, remember, set, simons, standard, table, treasure 4 Attachment(s)
    • Replies: 3
    • Views: 1,569
    Last Post: 30th June 2013 10:46 PM
    by Ueee  Go to last post

    Forum:
    METALWORK FORUM

  4. A Postcard from Linz

    Started by RayG, 10th July 2012 05:07 AM
    3 Pages •
    1 2 3
    aec, annual, bbq, bits, building, code, forum, galloping, garb, hardware, headquartered, horseback, idea, knight, knights, linz, medieval, millturn, missing, people, postcard, ray, ritter, ritterfest, saturday, simons, streets, thronged, workspace, youtube
    • Replies: 36
    • Views: 5,345
    Last Post: 5th September 2012 07:53 AM
    by Steamwhisperer  Go to last post

    Forum:
    METALWORK FORUM

  5. HM50 Can 'O' worms.....

    Started by Ueee, 26th June 2012 08:29 PM
    4 Pages •
    1 2 3 4
    .0003, axe, axis, badly, channels, clean, compensate, dovetails, error, flaked, hammer, hm50, ignore, knee, lube, machined, mic, o.k, plan, rc.s, saddle, scrapping, signs, simons, spotting, surfaces, table, thinking, wear, worms
    • Replies: 55
    • Views: 7,153
    Last Post: 19th July 2012 08:28 AM
    by eskimo  Go to last post

    Forum:
    METALWORK FORUM

  6. (Another) Low clearance deck in perth. [Long...]

    Started by mickfromperth, 8th July 2006 01:31 AM
    alot, archio, archios, bearer, bearers, built, clearance, concrete, deck, decking, directly, follow, ground, hangers, joist, joists, lead, learned, level, long, low, perth, read, reading, simons, sitting, stuff, support, supported, weight
    • Replies: 2
    • Views: 8,530
    Last Post: 15th November 2006 07:50 PM
    by GOON  Go to last post

    Forum:
    DECKING

Results 1 to 6 of 6