Search:

Tag: smudge

Search: Search took 0.00 seconds.

  1. gun regulator

    Started by sussertown, 29th December 2017 02:21 AM
    acetone, blurry, clean, damage, damaged, entire, feel, gun, husky, lacquer, lens, regulator, rough, smudge, spray
    • Replies: 7
    • Views: 9,764
    Last Post: 8th January 2018 12:22 PM
    by onetrack  Go to last post

    Forum:
    SPRAY FINISHES, AIR BRUSHING & DECORATIVE FINISHES

  2. Brown Mallee Burl

    Started by Penpal, 29th June 2013 08:07 AM
    adjust, biro, biros, brown, burl, cut, extended, fine, fun, hrs, iron, kits, line, mallee, manually, people, peter.2747922tsup, pump, repeat, slim, smudge, takes 2 Attachment(s)
    • Replies: 6
    • Views: 929
    Last Post: 29th June 2013 10:17 PM
    by bassmansimon  Go to last post

    Forum:
    WOODTURNING - PEN TURNING

  3. ink jet or laser for decals?

    Started by tdrumnut, 12th March 2013 06:08 PM
    bin, black, checked, cheers, colour, consideration, decals, decision, drum, factered, fuction, ink, jet, job, kaput, laser, lies, light, machine, multi, pens, printer, printers, printing, question, reason, replace, replacing, rumnut, smudge
    • Replies: 7
    • Views: 1,687
    Last Post: 21st March 2013 04:47 AM
    by Trent The Thief  Go to last post

    Forum:
    WOODTURNING - PEN TURNING

  4. Am I "Burning" the wood with my sander?

    Started by crash76, 5th October 2012 09:35 AM
    belt, black, brought, burning, charecteristic, corrugations, crash, grain, grit, job, marks, normal, paper, possibly, putting, redgum, sand, sanded, sander, sheet, slab, smudge, start, started, stripes, tiger, varnish, wood 7 Attachment(s)
    • Replies: 12
    • Views: 2,597
    Last Post: 5th October 2012 09:01 PM
    by DJ’s Timber  Go to last post

    Forum:
    FINISHING

  5. Clear coat dissolving stain

    Started by RussellB, 15th August 2010 12:23 AM
    action, apply, bit, brush, clear, coat, deeper, dissolving, finish, fix, hair, hand, increases, light, likelihood, patches, patchy, pressed, remove, requiring, result, smoothly, smudge, stain, sticky, surface, thicker, touched, touches, wide
    • Replies: 4
    • Views: 2,677
    Last Post: 18th August 2010 02:28 PM
    by RussellB  Go to last post

    Forum:
    FINISHING

  6. Query: how to burn a line

    Started by rsser, 19th May 2007 02:32 PM
    4 Pages •
    1 2 3 4
    30cm, bench;, bit, bowl, braided, browning, burn, couple, diameter, hard, heard, kitchen, laminate, laminex, line, lines, piece, plakky, possibilities, pressure, pulled, query, rim, smudge, stainless, success, tia, wander, wire
    • Replies: 53
    • Views: 5,771
    Last Post: 29th May 2007 01:24 PM
    by joe greiner  Go to last post

    Forum:
    WOODTURNING - GENERAL

  7. Triton dust respirator

    Started by jimj, 15th April 2007 07:34 AM
    age, bag, bottom, box, box.i, close, cloth, decks, discussed, dumb, dust, gear, glasses, hard, helmet, jim, mask, plastic, protective, question, remove, respirator, sand, sitting, smudge, storing, suggestions, timber, triton, wear
    • Replies: 8
    • Views: 1,879
    Last Post: 24th April 2007 11:24 PM
    by gyro  Go to last post

    Forum:
    TRITON / GMC

  8. Wire burning

    Started by joe greiner, 6th January 2007 04:45 AM
    afterthought, attached, box.-, burn, burning, diam, diy, effects, equator, gentler, guess, housing, impatient, jewellers, joe, knob, lens, match, measurement, off-latitude, perpendicular, produced, shown, slightly, slope, sloppy, smudge, upper, vignetting, wire
    • Replies: 14
    • Views: 3,286
    Last Post: 9th January 2007 12:51 AM
    by TTIT  Go to last post

    Forum:
    WOODTURNING - GENERAL

  9. Which wax over Danish Oil on dining table?

    Started by martrix, 28th February 2005 12:17 AM
    application, bees, bunnings, cabinet, carnuaba, coats, danish, dining, feast, finish, free, gilly, highly, liquid, makers, methods, nice, oil, recommend, redgum, sheen, smudge, stephensons, table, tim, true, watson, wax, waxs
    • Replies: 5
    • Views: 9,444
    Last Post: 22nd March 2005 08:19 AM
    by rsser  Go to last post

    Forum:
    FINISHING

Results 1 to 9 of 10