Search:

Tag: tother

Search: Search took 0.00 seconds.

  1. bench grinder question

    Started by old_picker, 8th May 2013 02:41 PM
    bad, barely, bench, buffing, coarse, compound, effect, fine, grinder, putting, question, reason, replace, stone, thinking, tother, type, uneven, weight, wheel, wondering
    • Replies: 6
    • Views: 1,762
    Last Post: 9th May 2013 01:31 PM
    by Jim Carroll  Go to last post

    Forum:
    GENERAL & SMALL MACHINERY

  2. Will wetted chipboard shrink back to original length?

    Started by Skew ChiDAMN!!, 12th February 2013 04:42 PM
    afaict, chipboard, dare, drawer, drawers, eyeball, fit, frame, front, gap, garbage, handles, hard, hardwood, inserted, inserting, katoomba, length, original, past, prior, push, rails, shrink, soaked, start, top, tother, veneered, wetted 1 Attachment(s)
    • Replies: 9
    • Views: 1,488
    Last Post: 13th February 2013 06:24 PM
    by Bob38S  Go to last post

    Forum:
    WOODWORK - GENERAL

  3. Two Small Mirrors

    Started by Woodwould, 7th January 2011 03:47 PM
    aged, antiqued, blemishes, brass, brasses, countersinks, enlarge, frames…, girandoles, hangers, item, londonderry, minor, mirrors, necessitated, photographer, picture, polish, polishing…, purchased, re-buffing, re-colouring, ready, screws, small, steel, tother, walnut, warm, wrath
    • Replies: 12
    • Views: 1,877
    Last Post: 14th January 2011 09:01 PM
    by Blue-deviled  Go to last post

    Forum:
    WOODWORK - GENERAL

  4. Small gloat

    Started by IanW, 22nd October 2010 12:16 PM
    bit, bits, cheeep, cheers, chunks, couple, day, fiddlebacked, finely, gauges, gidgee, gloat, lazarides, marking, nice, piece, pieces, qld, ring, small, spotted, squares, tother, value-add, walnut
    • Replies: 7
    • Views: 1,997
    Last Post: 24th October 2010 04:21 PM
    by Pops  Go to last post

    Forum:
    TIMBER

  5. Dressing the sides of an AlOx wheel?

    Started by Skew ChiDAMN!!, 30th March 2009 08:16 PM
    alox, balance, buy, check, common, conversation, cos, dress, dressed, dressing, earlier, flipped, hand, hed, line, mark, mentioned, pointless, potentially, rolleyes, sense, shaft, sides, started, tother, weeks, wheel, wobble, wobbling, wondering
    • Replies: 3
    • Views: 1,925
    Last Post: 31st March 2009 10:54 PM
    by Woodlee  Go to last post

    Forum:
    SHARPENING

  6. Oops!

    Started by Christopha, 15th August 2008 01:54 PM
    accidentally, bass, blasted, canon, clue, computer, day, deleted, deleting, disc, err, flamin, gratefully, house, insert, installed, means, moves, oops, printer, received, reconnect, roollly, roolly, s200sp, strewth, suggestions, time, tother, waaay
    • Replies: 9
    • Views: 1,840
    Last Post: 16th August 2008 12:34 AM
    by Christopha  Go to last post

    Forum:
    COMPUTERS

  7. another use for Blue Painters Tape

    Started by djfoggin, 20th June 2008 10:28 PM
    16mm, adjust, amount, bit, blue, box, dado, dados, dave, difficulty, distance, finish, fit, fits, honest, painters, pass, roll, rout, router, routs, set, shelf, shelves, shop, snugly, strip, tape, tother, undersize
    • Replies: 2
    • Views: 1,997
    Last Post: 1st July 2008 08:19 AM
    by Spreyton22  Go to last post

    Forum:
    ROUTING FORUM

  8. Some thoughts on sanding

    Started by LGS, 10th February 2008 03:05 PM
    400g, combination, conclusion, ets, ets150/3, finish, finishing, hear, method, oil, piece, playing, preferred, preparation, ro150, rob, sanders, sanding, saturating, set, similar, thoughts, tother, vacuum, wax
    • Replies: 9
    • Views: 1,930
    Last Post: 14th February 2008 02:02 PM
    by underused  Go to last post

    Forum:
    FESTOOL FORUM

  9. Aust Grasstree with a bullet.

    Started by Skew ChiDAMN!!, 5th September 2007 02:46 PM
    .30-03, .308, american, assembling, aust, australian, barrel, bullet, bullets, choice, dohb, finish, finished, finishes, flat-top, grasstree, kit, lower, match, oops, primer, realised, rolleyes, simply, sized, slimline, straight, suitably, tother, tubeless
    • Replies: 14
    • Views: 2,031
    Last Post: 5th September 2007 11:58 PM
    by PenTurner  Go to last post

    Forum:
    WOODTURNING - PEN TURNING

  10. Putting a glossy finish on corian?

    Started by Skew ChiDAMN!!, 19th May 2007 05:21 PM
    2 Pages •
    1 2
    basic, blank, buffing, carved, carving, concavities, corian, deep, detail, feeling, finish, gloss, glossy, idea, ideas, manage, match, naturellement, prefer, project, putting, rest, round, rule, sandpaper, section, sneaking, taking, tother, wink
    • Replies: 21
    • Views: 8,220
    Last Post: 28th May 2007 03:16 PM
    by thostorey  Go to last post

    Forum:
    WOODTURNING - GENERAL

Results 1 to 10 of 10