Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Newbie, need advise
-
2nd February 2011, 08:29 AM #1New Member
- Join Date
- Feb 2011
- Location
- Las Vegas
- Posts
- 6
Newbie, need advise
Hi guys, just found this forum and so far I'm loving it. This is my first project, a workbench. I'm using 3/4 inch plywood and top it with a tempered hardboard, light duty workbench. My question, what is the best way to glue the hardboard onto the plywood that is easy enough to peel off when it's needed for replacement?
Another thing, if I only choose the plywood without the hardboard, what varnish, paint or coating can I use to make the plywood little tough to chip or chemical resistant? thanks
-
2nd February 2011 08:29 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd February 2011, 09:12 AM #2
I know you guys have some more useful options in terms of ply, the stuff we generally get out this way is pine based and pretty aweful at that. If you can source some toughish ply, any good drying oil will toughen it further and make it glue and chemical resistance. Danish Oil, Tung Oil, Linseed Oil, etc.
As for reversable glue for the hardboard top, about the only thing I can think of is an aerosol contact adhesive. Any woodworking glue will be far to difficult to remove again. Of course you could just screw it down."Human beings, who are almost unique in having the ability to learn from the experience of others, are also remarkable for their apparent disinclination to do so."
- Douglas Adams
-
2nd February 2011, 10:12 AM #3New Member
- Join Date
- Feb 2011
- Location
- Las Vegas
- Posts
- 6
Thanks for the response. The plywood is hardwood and on expensive side, not liking that. I think I will try the oil first and see how it comes out. If I choose to apply the hardboard I can just use screws like you said. Should I screw it all around and middle or just enough to hold?
-
2nd February 2011, 11:53 AM #4
I guess the idea with screws would be just enought to stop the edges/corners from lifting and keep the centre in contact with the ply.
I have seen people put a hardwood apron around the edge which the hardboard sits inside. No screws, no glue and very easy to replace and clean up if any debris get into the gaps."Human beings, who are almost unique in having the ability to learn from the experience of others, are also remarkable for their apparent disinclination to do so."
- Douglas Adams
-
2nd February 2011, 12:21 PM #5New Member
- Join Date
- Feb 2011
- Location
- Las Vegas
- Posts
- 6
Putting screws just on the corner sounds good, thanks
-
2nd February 2011, 11:06 PM #6
For easiest placement and removal, I'd suggest no glue, and no screws. Instead, use short box nails at the perimeter. I think that's how Nawm (Abrams, New Yankee Workshop) does it.
Cheers,
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
3rd February 2011, 01:29 AM #7New Member
- Join Date
- Feb 2011
- Location
- Las Vegas
- Posts
- 6
I'll check that option out, thanks
-
5th February 2011, 09:47 PM #8
More than one way to skin a cat eh?
Reality is no background music.
Cheers John
-
6th February 2011, 03:32 AM #9New Member
- Join Date
- Feb 2011
- Location
- Las Vegas
- Posts
- 6
Sure does. This is the bench halfway done, it's 84"x30". I just use the legs from 2x4 basics, this shows the lack of knowledge in this field but it's a start.
I don't really do any woodworking but I hope to pick up some ideas from the members. Anyway, here it is.
-
8th February 2011, 02:58 AM #10Intermediate Member
- Join Date
- Aug 2010
- Location
- singapore
- Posts
- 31
Nice workbench
Its a nice workbench you got there. Do you intend to use power tools, hand tools or both? You may like to consider a vise if you intend to use hand tools.
You may also want to think about how you would construct a top with an overhang in future to facilitate clamping. Nice workbench
-
8th February 2011, 10:34 AM #11New Member
- Join Date
- Feb 2011
- Location
- Las Vegas
- Posts
- 6
Thanks. I'm just going to put a pegboard for my few tools. For now it's just for tool keeping and a hangout bench in the garage for time alone Maybe I'll pick up a book to start a project.
Similar Threads
-
nEED ADVISE ON HEADLIGHTS
By Bleedin Thumb in forum MOTOR VEHICLESReplies: 23Last Post: 21st July 2007, 08:21 PM -
Glue Advise
By woodtryer in forum GLUEReplies: 3Last Post: 25th July 2006, 08:46 PM -
new at this advise please?
By peterowensbabs in forum WOODTURNING - GENERALReplies: 15Last Post: 17th October 2004, 11:02 AM -
Advise
By Harry II in forum BANDSAWSReplies: 10Last Post: 11th November 2002, 12:36 AM