Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Bandsaw Guides...
-
25th October 2013, 11:27 PM #1Novice
- Join Date
- May 2007
- Location
- Perth
- Posts
- 24
Bandsaw Guides...
I've recently purchased a bandsaw, and it was suppled with the euro style GL456 brass bushing upper guide, and a wooden block lower guide.
The saw will be used for blades from 1/4" and up to 1".
Carter guides (eg. Euro 600) would set me back a lot of money like $500+ - - and I'm pretty sure it's not value for money.
But I am thinking about whether it's worth upgrading the lower guides to a matching GL456 guide.
Appreciate any advice on guides and the law of diminishing returns ?
-
25th October 2013 11:27 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
29th October 2013, 06:55 AM #2
Try ceramic guides, they much support all around.
-
29th October 2013, 08:17 AM #3Novice
- Join Date
- May 2007
- Location
- Perth
- Posts
- 24
Thanks for the tip. After some thought, one guide would not do the job.
I ordered Laguna ceramic guides and a Carter stabilizer for 1/4" and finer curve cutting.
If I get another smaller saw eg 14" if will most likely be a Laguna or similar.
-
29th October 2013, 11:17 AM #4
By Carter guides I assume that you mean the roller bearing style, rather than block bearings?
IMHO they're normally well worth it, but $500?? I can see your concern about cost-benefit... I doubt they'll improve the "ruggedness and blade durability" that much!
At this stage Bosox' suggestion seems the better way to go - for now - as replacing both upper & lower with ceramics would be the best splash for your cash. (And yes, upgrading both sets is a damned good idea if you're concerned about accuracy with minimal fussing. )
However, even so, I'd keep an eye out for an alternate set of good roller bearing guides that won't break your bank balance. I believe they're worth it.
(I'm assuming that your BS will be an every-day user that is used for everything from ripping down large boards to fine scroll-work; which is where it excels. If it's only an occasional user, then cost:benefit becomes trickier to calculate in day-to-day terms.)
- Andy Mc
-
29th October 2013, 11:19 AM #5
Dunno how I missed your reply to bosox, but I did.
Good choice! Hope they serve you well.
- Andy Mc
-
29th October 2013, 02:50 PM #6Senior Member
- Join Date
- Apr 2010
- Location
- Adelaide
- Posts
- 191
I'll be interested to hear if your bandsaw has the flat euro style wheels where you set the blade teeth to be just off the front edge of the top wheel. I have one of that style and am strongly considering putting a 'bevel' on the wheels so they can run on the center as most of the bandsaws i've used and setup tend to have nowdays. Good to see you found some new guides too, will be very interested to hear how they perform. I've also heard of people making epoxy and graphite blocks to use on the bandsaw, if the ceramic ones for whatever reason don't work out so well.
Cheers
- I am slowly building an Ian Oughtred lapstrake (6 planks) Macgregor Canoe it should have 2 sails when finished as well
-
5th November 2013, 09:00 PM #7Novice
- Join Date
- May 2007
- Location
- Perth
- Posts
- 24
Yes it has a flat wheel tyre and I'm just setting up a 1/4" blade. Doesn't seem to track well unless the blade is in the middle. The rear guide hits the guard if the blade is on the edge so that is also an issue.
Should be easier with the more conventional 1/2" blades to get it to track well (I hope)
-
6th November 2013, 12:41 PM #8Senior Member
- Join Date
- Apr 2010
- Location
- Adelaide
- Posts
- 191
-
9th November 2013, 01:42 PM #9Novice
- Join Date
- May 2007
- Location
- Perth
- Posts
- 24
Sorry I meant to say Thrust bearing.. But got it all sorted out.
Been a big weekend. Got my clearvue running and the saw is working great.
Similar Threads
-
bandsaw guides
By Ross arnold in forum BANDSAWSReplies: 2Last Post: 6th May 2012, 11:22 PM -
Bandsaw guides
By Poliocephalus in forum BANDSAWSReplies: 4Last Post: 13th October 2010, 08:24 AM -
bandsaw guides
By John Balloch in forum BANDSAWSReplies: 5Last Post: 9th September 2010, 11:08 PM -
more on bandsaw guides
By mongrell in forum BANDSAWSReplies: 2Last Post: 23rd September 2006, 07:33 PM -
bandsaw guides
By Budge in forum BANDSAWSReplies: 1Last Post: 16th July 2006, 12:45 AM