- In praise of Ozito tools
- Staining a pine corner unit
- ID cupboard and timber please
- Advice needed to prepare garage rendered brick walls for Paulk Cabinets.
- timber slab steel frame?
- Staining Tas oak/vic ash
- Aldi 'Planer Thicknesser'
- Feral Pegs
- When you head does not work properly
- Seen this add for plans
- Clean new machinery
- Clear epoxy resin to highlight the cracks&holes in old, now milled sleepers assistanc
- Anyone with experience setting up a Masterwood OMB1V?
- Dewalt 735 thicknesser blown motor
- Slab Table for the Deck - Phase 1
- Green Camphor Laurel
- I told you I'd get around to it.....
- Baby safe finish for Cot
- Cracks in blackbutt - filling suggestions without epoxy
- Slab Coffee Table WIP
- Nannas Chiswell Telephone Table
- How well will CA prevent small screws from working loose in a scissor action piece?
- The Beenleigh Sunday Markets
- Complimentary timber for Sheoak
- Shaker Music Stand
- Wooden Ring request.
- What brand of glue?
- Gray streaks in dressed pine
- Which 9 1/4" (235mm) saw blade for ripping hard wood?
- What timber is this?
- plywood bending
- durden
- Ledge and Brace door question.
- HELP. Need some red cedar veneer
- Wooden Car
- My first 'big' project - Carriage style barn doors
- Use of Band saw Adelaide
- Retro fitting anti-con
- I am a woodwork failure.
- To biscuit, or not to biscuit
- best way to build my new front doors help please
- leg size advice
- Sawdust putty
- Flexible Plywood in small quantities? Bending single layer of flexible Plywood?
- Finish for a Timber Sink
- Which type of end for a tuart table top ?
- Stability of a bookmatched table top.
- Yr 12 HSC Major Project feedback
- Old Magazine article required
- Knife Sharpening in S.E. Melbourne
- Traditional mortice and tenon proportions
- Replacement draw slide.
- Cabinet Style
- Pallet timber (is it safe) in Australia
- Taking router lifts to the next level
- Chess Board for #2 son - progress, questions, feedback and advice welcome
- Stapling Canvas to stretcher bar
- Squaring end of timber
- How would you make this joint?
- Lightbulb moment.
- What are these pieces called and where can I buy some?
- Safe glues and paints for wood toys
- Melbourne Get togethers
- New-ish Bunnings in Chadstone. 7 weeks new. Nice and clean and attentive.
- Hettich drawer front connector
- My first serious woodworking project besides rough pine stuff and DIY jobs
- Thicknesser advice needed
- Carbatec quick release vise
- Table top fasteners
- Moxon Vise
- mortice chisel angle
- Can anyone recommend a good carpenter around Revesby area?
- Whatsitfor?
- Refinished chair
- Circular saw Straight Edge
- Coffee table WIP
- Finish for Huon Pine
- Making a door
- Some Brass Rings.
- Lazy Susan bearing plus thrust bearing - how much torque?
- Compound cupboard door hinge with pivot hinge mounting
- Wife's changed her mind
- Awesome Innovation!!
- Jointer and Thicknesser in North Brisbane
- My ARN Woodshop - Out of storage and into the shop.
- Cypress Pine Planter's Cracking
- Gotta rid myself of Dust
- Advice installing T-Track in 16mm MDF
- Fire in the workshop!
- Merbau Cabinet Door
- Mitre box for wide boards
- Anyone her living or working near Hurstville or Kogara area, Sydney?
- Another hinge question.
- Anyone know what these piles are from?
- A small celebration, and a request for help
- Oneway Multi Gauge in Australia
- The geometry of Gothic tracery
- Question about Butt Hinge Rebates for Inside Hung Doors
- Looking for a project idea to use these one pound brass hinges
- Magnets
- Coating a Hoop Pine Sign for Outdoors?
- Festool Domino
- Festool dominos
- collective noun for clamps
- Melbourne timber and working with wood show 2016
- Making a Nelson bench - what timber to use
- Potential Liability??
- Cupboars doors.
- Attaching tabletop using oversized pocket holes?
- Double sided bandsaw blade
- Hi, from the Goldfields
- Advice on Aussie hardwood for toy wheel making please....
- Imperial size Dowel
- Another plantation shutter thread....
- Advice on Door making
- Gifkins replacement parts
- Hard Maple and Jarrah side tables - part 1
- How is this chair made
- Delivery from Mapleman
- Portable sheet cutting bench sorta thing
- Timber type for hinge
- Slab Table Width
- Australian furniture making (techniques) book
- Ripping 50mm thick Ironbark?
- Remodelling blackwood cabinet
- Shaker style cabinets - joinery options
- Hard Maple and Jarrah side tables - Part 2 of 2
- i thought treated sleepers would not rot?
- Use of table saw Adelaide
- Watch "Complete retrofit car stereo in a '42 Philco Radio" on YouTube
- Second Hand electric motors
- Dovetail joints for beginners
- Rim Guided Forstner Bit query
- Moisture meter and oil content of wood?
- Clogged drum sander belts
- Pine chairs
- Student worK
- Figured maple and Walnut hall table
- Paslode 32mm C-Brads - hot dip galvanised or not?
- Need help on how to square up one edge on rough lumber
- 16ga stainless steel (316 grade) 32mm brad nails - where to get?
- Guitar players advice needed.
- Youtube woodworking videos
- Torquata Parallel Clamps from Timbecon
- Greg Smith
- epoxy filling and stabilising
- Strange Paint Deal At Local M10 Store
- Help with a creative Business Name
- Odd Hinges - Need help to find a set
- Beeswax