Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 24 of 24
Thread: Filling holes
-
15th June 2008, 09:51 AM #16
I don't worry about that as the sander cleans it all up nicely.
It will also take a lot of heat and would make a good pewter moulds.
-
15th June 2008 09:51 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th June 2008, 10:09 AM #17
Went out the shed earlier and the filler is still moist.
If I sand it now it will clog the paper so I've put a heater on. I've also taken a few pics that I'll post a bit later.
-
15th June 2008, 10:11 AM #18
-
15th June 2008, 09:12 PM #19
I'd suggest "timbermate"
http://www.timbermate.com.au/products/timbermate.html
great stuff.
I've used it to fill nail holes on recycled oregon I used for kitchen cupboard doors
You could also probably try the tinted wax sticks thwt restorers use
-
15th June 2008, 09:19 PM #20
-
15th June 2008, 09:39 PM #21
Pics, finally.
First few pics show the amount of fill, a lot of them are 1cm deep or more.
Note the second pic, it shows the filler is still not dry after sitting overnight. This, I think, is because of the very cold weather and the tint I added. More practice should reveal more information.
Pic three - after rough sanding. I have decided to get rid of my makita 1/3 sheet sander after today. Because of the mess I thought I'd use the Mak and some cheap sandpaper, what a mess! Dust everywhere and it smeared the dye into the rest of the timber, whereas the Makita BO6030 ROS just sucked it up and kept it tidy. Note I have found the first limitation of the Aldi shop-vac - this thing clogs the filter pretty easily when sanding; I might look into getting a second hand Triton suck-bucket.
Four - the tint went deep into the timber surface and took a bit of sanding to get it out.
Five - after prep sanding they don't look too bad (yeah ok, these are the faces )
Six - the timber for the bench rails showing the builders bog after sanding. It turns deep black (oxides mixed with it) once finished. Note the Aldi shop-vac sitting to the left, it worked very well for about 6 hours straight today
-
15th June 2008, 11:07 PM #22
Gawd
pic 1 looks like it's come out in some sort of rash
hope you've kept the vaccinations up to date
-
16th June 2008, 12:40 AM #23
Mike
I've had success with 5 minute araldite tinted with powdered pigments (oxides?)
Did some small holes in my floor the night before it was sanded and tongue oiled 10 years ago. The patching has stood up for 10 years so far.
Richard Vaughan showed me the technique
I mixed the pigments into the darker coloured part till I got the colour match I wanted, then added the clear part and filled the hole.
Being 5 minute araldite and varied coloured boards, I worked on only 2 or 3 holes at a time.
From memory, I had a colour palet of 4 or 5 shades of brown (from red through to chocolate) plus black
cheers
ian
-
16th June 2008, 12:46 AM #24
Thanks, all good information. The more options the better, then I can get totally confused
Cheers,
Mike
Similar Threads
-
filling holes in slabs
By Rosethorn in forum WOODWORK - GENERALReplies: 23Last Post: 19th March 2007, 07:44 PM -
Filling screw holes?
By Santalum in forum WOODWORK - GENERALReplies: 5Last Post: 2nd May 2005, 09:12 AM -
Filling screw holes
By Strungout in forum WOODWORK - GENERALReplies: 2Last Post: 14th November 2004, 10:24 PM -
Filling borer holes
By Paul Swinhoe in forum FINISHINGReplies: 2Last Post: 7th April 2004, 07:58 AM