Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
-
19th December 2008, 04:04 PM #1Novice
- Join Date
- Nov 2008
- Location
- Tas
- Posts
- 16
how to rip a piece of timber at an angle without a table saw?
Is it possible?
I want to make pieces shaped like a Toblerone, pyramid at the sides.
Cheers
-
19th December 2008 04:04 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
19th December 2008, 04:41 PM #2
I'm not sure what 'Toblerone" looks like but if you are talking curves, or the like, then a router (a most versatile tool) may be what you're after.
soth
-
19th December 2008, 04:43 PM #3Novice
- Join Date
- Nov 2008
- Location
- Tas
- Posts
- 16
http://en.wikipedia.org/wiki/Toblerone Looking at the box, not its contents.
-
19th December 2008, 04:46 PM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,829
-
19th December 2008, 04:49 PM #5
Mate, anything's possible with a bit of persistance
What tools do you have?
How big a piece of timber are you working with?
As a 15 year old kid I recall making a 26'' fixed pitch propeller out of a bit of 4 x 2 with a bow saw and a rasp to fit to old victa engine to make an airboat we used on the Barron River at Mareeba NQ. In fact I made two because I needed to reverse the pitch to make it a pusher. (The prop was too close to the back of my head )
A toblerone block of chocolate should be a doddle!!
Ian
-
19th December 2008, 05:21 PM #6Novice
- Join Date
- Nov 2008
- Location
- Tas
- Posts
- 16
okay, a bit more info. I'm building the kids a cubby house that's meant to end up looking like a castle.
This means that there won't be a roof and that the top of the walls will be exposed. Along these walls will be crenallations. On top of each crenallation will be one of the toblerone-like pieces, which main purpose is to prevent rain water from sitting on the bare pine.
Because the crenallations are staggered the pieces don't have to be very long, probably 50mm. While the angle isn't that important, being able to replicate the angle on more than one piece is.
I've got most tools, aside from any table tools. So I have a standalone router, jigsaw, etc.
-
19th December 2008, 05:22 PM #7Novice
- Join Date
- Nov 2008
- Location
- Tas
- Posts
- 16
what I've got so far
-
19th December 2008, 05:28 PM #8
A circular saw (skill-saw) with the blade set at an appropriate angle (30* ??) should do the job. It might be worth using a couple of similar thickness boards as sawplate rests to stop the saw wobling or tilting during the cut.
Merry Christmas
Graeme
-
19th December 2008, 05:30 PM #9.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,829
I would buy some plastic angle and nail it direct onto the pine.
-
19th December 2008, 05:37 PM #10
You've got three options as I see it:
Find a mate with a table saw or a band saw
Buy a table saw or a bandsaw (or both)
Mark up and clamp short lengths in that sorry looking Superjaws of yours and attack then with a hand saw
Ian
-
19th December 2008, 05:51 PM #11SENIOR MEMBER
- Join Date
- Feb 2007
- Location
- Adelaide
- Posts
- 595
If you start with a fairly wide board, bevel one edge (set your circular saw at an angle and run it along a straight edge) Then, turn the board over and dock off the bevelled piece. Repeat until you have the lengths you need. Your board will have to be wide enough at the start though to support your circular saw base and the clamped straightedge.
Similar Threads
-
Groove in small piece of timber
By STAR in forum WOODWORK - GENERALReplies: 3Last Post: 11th April 2008, 02:25 PM -
Work piece direction in table.
By hawkinob in forum ROUTING FORUMReplies: 12Last Post: 5th February 2008, 05:32 PM -
A question about table saws and cutting on an angle.
By Crawford in forum WOODWORK - GENERALReplies: 9Last Post: 25th March 2007, 08:16 AM -
Fore/aft adjustment of table angle (Sherwood BAS-350)?
By zenwood in forum BANDSAWSReplies: 14Last Post: 5th August 2005, 01:36 PM