Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: Best tool for this job
-
25th March 2012, 09:47 AM #1
Best tool for this job
There was a recent thread about fixing a post with rot and that reminded me about my experience with a post that had rotted at the base but otherwise it was ok. The post is part of a weatherboard clad shed and is about 90 by 90 mm in dimension. The post is clad with weatherboards on one side and at right angles to that there is another wall stud so in essence the post is bordered on 2 sides and on 2 sides it isn't. Anyway I wanted to cut out the rotted bottom portion and splice in a new bit of timber, I couldn't really use a circular saw because the post is bordered on 2 sides and my saw doesn't have a depth of 90 mm. I used a handsaw for some of the job and then resorted to hammer and chisel but the post was flexing because it wasn't attached to the bottom sill (as the base of the post was rotted) so the chisel wasn't all that effective. My question is what power tool could have helped here to remove the rotted portion in order to take a new spliced bit of wood?
-
25th March 2012 09:47 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
25th March 2012, 12:12 PM #2Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,126
Fein multi master or similar oscillating tool
-
25th March 2012, 12:43 PM #3
Do the oscillating tools have a depth of 90 mm?
-
25th March 2012, 01:33 PM #4Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,126
Good point, didnt think of that. Sabre saw perhaps?
-
25th March 2012, 01:50 PM #5GOLD MEMBER
- Join Date
- Aug 2007
- Location
- Brisbane
- Posts
- 1,156
I don't know much about sds drills, but if you can get chisel sharp bits then that may work. You'd have the problem with flex still, but with power on your side it should go quicker. Only thing I thought of was something like an arbortech, but I don't think you'd get the depth of cut. Small chainsaw maybe? You'd still have a corner to get through due to the rounded shape of the bar end. You could mark the depth onto the bar to make sure you don't go too far through.
The other day I described to my daughter how to find something in the garage by saying "It's right near my big saw". A few minutes later she came back to ask: "Do you mean the black one, the green one, or the blue one?".
-
25th March 2012, 10:50 PM #6GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,567
If there is just a bit of clearance between post and cladding you could use a wire saw.
-
26th March 2012, 12:55 AM #7Member
- Join Date
- May 2009
- Location
- Geraldton
- Posts
- 71
The arbortech all saw should do the job pretty painlessly
Ben
-
26th March 2012, 10:29 AM #8
Thanks Ben, Peter, Rusty and EJ. Good ideas and I already own half the tools mentioned. The arbortech saw is one I wouldn't have considered but providing it can do other jobs as well then that'll be enough reason to buy one.
-
26th March 2012, 11:35 AM #9
For a one off job, Rather than buy a tool to use once, I would use an old fashion key hole saw. You would need to bore three or four 3/16" holes close together first to get the saw blade in to start.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
26th March 2012, 12:00 PM #10Senior Member
- Join Date
- Sep 2007
- Location
- Country West Oz
- Age
- 77
- Posts
- 201
-
26th March 2012, 04:18 PM #11
Thanks Jim and Bradford. Jim, like your solution, I must have about 4 keyhole saws at home but the blades on all of them are deformed or blunt.
Bradford, yep 250 mm would do it, do they come standard with these tools or is that a special after sale purchase?
-
27th March 2012, 08:27 AM #12Senior Member
- Join Date
- Oct 2004
- Location
- Goondiwindi Qld
- Posts
- 261
I suppose there must be a reason you can't remove one or the other cladding boards and simply cut through with whatever you have.
Regards, Bill
-
27th March 2012, 09:50 AM #13
-
27th March 2012, 03:54 PM #14Senior Member
- Join Date
- Sep 2007
- Location
- Country West Oz
- Age
- 77
- Posts
- 201
I've got myself at cross purposes here, everybody is saying oscillating and I'm thinking recipricating (not sure of the spelling). Anyway I do have 250mm blades for my recipricating saw and they were an after sale purchase, I recall they were fairly expensive, can't remember how much though.
Regards
Bradford
Similar Threads
-
SOMETHING NEW! Hand Tool Preservation Assoc. of Aust. Tool Sale.
By issatree in forum ANNOUNCEMENTSReplies: 12Last Post: 19th March 2012, 02:07 PM -
Parting tool mounted on rear tool post advice needed
By colbra in forum METALWORK FORUMReplies: 17Last Post: 12th February 2012, 02:49 PM -
Hand Tool Preservation, Tool Sale,2011.
By issatree in forum ANNOUNCEMENTSReplies: 5Last Post: 9th July 2011, 11:03 AM -
Hand Tool Preservation Tool Sale.
By issatree in forum ANNOUNCEMENTSReplies: 3Last Post: 5th November 2010, 11:11 PM -
Hand Tool Preservation Society Tool Sale
By Clinton in forum ANNOUNCEMENTSReplies: 0Last Post: 15th July 2005, 01:47 PM