Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 22 of 22
Thread: Which circular saw to buy?
-
9th February 2007, 10:18 PM #16
-
9th February 2007 10:18 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th February 2007, 10:32 PM #17
Yeah, I reckon for demo work, nails, and such, a reciprocating saw is the go. Cheap blades, lots of power, different blades for metal, etc.
Over here we commonly refer to a recip as a sawzall (although that is actually a brand name of the saw produced by Milwaukee Tools).Cheers,
Bob
-
9th February 2007, 10:41 PM #18.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Ive been babysitting a TS75, and yes its very exy, but Wooooha...... Its on another planet as a circular saw to the rest. I realy dont know how im going to cope when i have to hand it back
-
9th February 2007, 10:42 PM #19SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Sydney
- Age
- 63
- Posts
- 1,619
I never throw out my old saw blades. You can chuck them in an angle grinder and you've got a big arbortech carver that cuts almost flush with a surface. No base plate to get in the way. You'd be surprised at how many nails you can get through before a tungsten blade is cactus. It's usually the heat from the timber that distorts it in the end. It gets a bit nerve wracking when the blade starts to wobble all over the place.
I haven't heard of that one. You can chuck a blade backwards into a circular saw and cut sheets of corro with it. It will cut quite a distance before the teeth all get ripped off.
The blades are horrendously expensive though, and they don't last long before they're blunt, or they just snap.
-
11th February 2007, 01:23 PM #20Member
- Join Date
- Feb 2007
- Location
- Yackandandah
- Posts
- 50
A reciprocating saw is a good alternative for cutting in difficult "nailey"places.
Except I dont own one+ living in a rural area I have 2 chainsaws anyway.. Reciprocating saws tend to jump around a bit.
apparently the SES [State Emergency Service ] use an expensive type of blade to cut thru car rooves to cut people out after car accidents!!
-
11th February 2007, 05:15 PM #21.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,814
Since no one appears to have answered, UHMW is Ultra High Molecular weight "something", usually Polyethylene, so a full abbrev should be UHMWPE.
A wiki check should reveal more than you need to know.
Cheers
-
11th February 2007, 05:35 PM #22
Gidday
I've got a 9 1/4 Hitachi C9 Just keeps goin an always delivers the goods so far appears bullet proof n has a heafty solid base. Coupled with a top quality blade n the EZ Smartguide n you've got one of the handiest piece a kits in the the shop!
With this setup & a well thought out cutting table say buy buy to the hassle of cutting up man made sheet goods believe it or not I can accurately RIP 200 inches safely without fear of kickback n carve up sheet goods to my specs in a breeze.
REgards LouJust Do The Best You Can With What You HAve At The Time
Similar Threads
-
Circular Saw Zero Clearance
By brucen in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 7Last Post: 7th May 2005, 07:42 AM -
Which compressor and nail gun would you buy...and why?
By kando in forum HAND TOOLS - POWEREDReplies: 14Last Post: 14th January 2005, 12:35 PM -
To buy or not to buy...?
By Medal Collector in forum FESTOOL FORUMReplies: 8Last Post: 27th October 2004, 09:15 PM -
User Review: Cheap 19volt cordless circular saw
By paul.cleary in forum HAND TOOLS - POWEREDReplies: 0Last Post: 23rd August 2004, 11:49 AM -
Brissie Woodies - Bulk K-Body clamp buy
By Dean in forum WOODWORK - GENERALReplies: 26Last Post: 25th July 2004, 11:36 PM