Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Makita Bearings
-
16th June 2009, 07:41 PM #1Senior Member
- Join Date
- Aug 2006
- Location
- Melbourne
- Posts
- 400
Makita Bearings
Hi,
I have an old Makita LS1400 mitre saw that I would like to replace the bearings on, it still works fine, just has a bit of noise.
Was just wondering if there is anywhere other than makita that I can source the bearings from and what would I expect to pay?
I've got the saw apart at the moment. It has 3 bearings, would it be wise to replace all 3?
Thanks
-
16th June 2009 07:41 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
16th June 2009, 07:54 PM #2Member
- Join Date
- Nov 2005
- Location
- Kihikihi, TeAwamutu
- Age
- 80
- Posts
- 98
I had a saw that I brought from the UK and there were no agents for it in NZ. I took the bearings to a car parts shop similar to Repco and they measured and supplied the correct bearings for a very reasonable price. The saw (Delta) is still going great.
-
16th June 2009, 08:41 PM #3
Just did a quick search and found this place http://www.minibearings.com.au/distributors/vic/ Im sure that you will find other places that sell bearings your after.
I would replace all 3 bearings.Regards
Al .
You don't know, what you don't know, until you know it.
-
16th June 2009, 09:26 PM #4
Seeing that you have the machine apart, you should be able to pull the bearings out or at least read the part number on them of which is a universal number regardless of brand and it'd pay for you to visit your local wholesale bearing supplier where you can expect to pay about a 1/3rd of the cost if you were to source them from a Licensed Makita shop or tool repair joint.
From a bearing wholesaler, I'd expect to pay about $5 to $10 each depending on size of bearings or from a Makita or tool joint $20 to $50 each depending on how generous they areCheers
DJ
ADMIN
-
16th June 2009, 10:17 PM #5the tool specialists
- Join Date
- Jul 2007
- Location
- Smithfield,NSW
- Posts
- 365
Beware of the cheap chinese bearings, spend the extra & get the japanese bearings there is a significant difference.
We had a supplier give us the talk up that there was no difference just price $1 on average, after tests with some tools we found them to be to high a risk. If a bearing fails 7 you have to replace under warranty the labour outways the price of the bearings, customers are happy to pay $10-$20 for quality bearings we have found over the past 20years....if we were charging $20-50 I wouldnt be able to sleep at night...on thhe other hand i spose i would have plenty of money to entertain myself
-
21st June 2009, 01:58 PM #6Senior Member
- Join Date
- Aug 2006
- Location
- Melbourne
- Posts
- 400
Thanks for all the advice,
I will try and get to a bearing shop in the next few weeks. The bearings on it at the moment are NSK and state they are made in japan and a part number.
Is this the type of bearing puller i'll need, i've got a 3 jaw at the moment but dont think there is enough space to use it.
http://cgi.ebay.com.au/2-1-4-CAPACIT...3A1%7C294%3A50
Also when it comes to putting the new bearings back on are they pressed or can you use a soft faced hammer?
Thanks
-
21st June 2009, 02:20 PM #7
If the bearings arn't sealed , ie a cover on both sides covering the balls , put them in the onev at 180 deg for 20 minutes , have everything ready clean shaft etc, using gloves take the bearing out of the oven and slide it on, the heating will expand the bearing so its an easy slide on
Better not to use a soft or copper hammer to tap bearings on as flakes can come off the face and get into the bearing , if you have to tap one on use a small pin punch and tap the center ring down the shaft being carefull not to mark the shaft , two people doing this from either side working together is best or use a piece op pipe that just fits over the shaft and sits on the inner ring of the bearing to tap it home,Ashore
The trouble with life is there's no background music.
Similar Threads
-
New Bearings Woodfast
By Edward Tabachek in forum WOODTURNING - GENERALReplies: 14Last Post: 5th September 2022, 01:31 PM -
Pulleys and bearings
By jmk89 in forum METALWORK FORUMReplies: 0Last Post: 6th March 2008, 02:48 PM -
Thruster Bearings
By Cruzi in forum BANDSAWSReplies: 2Last Post: 19th October 2007, 12:05 PM -
Lathe Bearings
By Ivan Wadsworth in forum WOODTURNING - GENERALReplies: 1Last Post: 10th January 2006, 12:01 PM -
Bearings
By smidsy in forum ROUTING FORUMReplies: 10Last Post: 10th November 2005, 09:46 PM