Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
13th November 2017, 10:26 PM #1Member
- Join Date
- Nov 2009
- Location
- Ocean Grove, Vic
- Posts
- 70
Any recommendations milling service near Traralgon, Victoria. Silky oak 1.5m diameter
Hi all, my parents in Traralgon need to have a large silky oak felled and I'm looking for recommendations for people able to fell it safely and then mill it (not necessarily the same person doing both of course!). It's at least 15 metres high and 1.5 metres diameter, 2 metres from the house and has about as 10 degree lean (away from the house thank goodness, but still could be exciting). From previous projects I love the look and feel of silky oak and am keen to have it milled properly.
I'm fully aware that a large heavy tree near a house with some lean isn't going to be cheap to fell and mill up, appreciate expertise and equipment isn't free. Happy to pay in silky oak, money or (far the most likely!!) both.
Also appreciate any advice on what to do with it in large boards or even beams. The biggest bit I've ever used was to make a chair seat but I reckon table tops and sideboards would look fantastic. I'm aware I'm counting my timber before I've checked it for rot, but I'm still excited.
Thanks for any advice offered, Dan
-
13th November 2017 10:26 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
14th November 2017, 08:26 AM #2GOLD MEMBER
- Join Date
- Jan 2013
- Location
- the sawdust factory, FNQ
- Posts
- 1,051
To be clear here: 1.5m diameter or 1.5m girth/circumference?
No offense meant but it's surprising how many confuse the two. Ones a decent log and the other's a monster and the gear you need to tackle them is very different.
-
14th November 2017, 09:28 AM #3Member
- Join Date
- Nov 2009
- Location
- Ocean Grove, Vic
- Posts
- 70
No offence taken John. I'm clear on the mathematics, diameter 1.5m, radius 750mm. I'm told that's the dimension at the root flare, the trunk would be smaller but well over a metre. It's an old, thick tree. However, since I haven't measured it myself I might ask my brother what technique he used to measure it, get him to pass a string around it and divide by pi to be precise on the diameter. Or would arborists prefer the circumference?
I've got cold feet now, have to check my homework and repost exact dimensions, but BIIIG. Should I get him to measure it from the root flare 150mm above the ground, or from where the trunk is a more consistent thickness? Thanks for your interest John
-
14th November 2017, 10:44 AM #4GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,564
The usual method is to measure at breast height. This gets away from the roots and gives a measurement more pertaining to the log itself.
To obtain the best figure in the timber it should be quarter sawn. This method gets the best from the medullary rays which are prominent in silky oak. Flat or back sawn lacks the lacy look so typical of the oaks.
This sounds like a big stick and requires someone with a few clues. Not for your average backyard warrior. Logistics (pardon the pun) are going to play an important part here. A log of these dimensions is going to require some grunt to move it about. A good job for a Lucasmill and a carve-up on site.
-
15th November 2017, 07:40 AM #5GOLD MEMBER
- Join Date
- Jan 2013
- Location
- the sawdust factory, FNQ
- Posts
- 1,051
What Ken said.
Look it been there a few years and unless there's some urgent reason to drop it a few more weeks wont hurt. So think your way through it and get your ducks in a row first kinda thing.
Is the trunk basically straight (even if leaning) and cylindrical? If so and theres no rot, no big lumps etc it could well be suitable for export/veneer. Despite urban legend you can't get rich off a single sawlog but there's pretty good money in it. Say a 10m log with average diameter of 600 and youd be looking at 23/4 cube of log. $1200 a cube for export to pick the last oak we sold ( while back and might be way out) and theres an easy $3k. As a sawmiller I cannot make as much profit sawing logs like that as I can sending them to China. Sad but true.
If hes got rot in him I'd suggest a lucas mill as the best machine for the job but if solid id be thinking about a bandmill, even though it might mean freehand ripping to quarters with a chainsaw. The premium for chasing the grain is worth the lower recovery and a bandmill with hydraulic clamping will give you a higher value product. But you need width to make that pay.
Lotsa pictures please
-
16th November 2017, 08:43 AM #6
Remember...it could be full of metal too...MM
Mapleman
-
18th May 2018, 12:25 PM #7GOLD MEMBER
- Join Date
- Apr 2015
- Location
- Warragul Vic
- Posts
- 1,093
Would love to see & read some follow up to what happened Dan.
Please keep us informed of what you chose to do and how it went.
Hope the sawmillers & fellers are careful as the wet sap from most grevilleas like this one is very irritating to skin and eyes.
Similar Threads
-
Victoria (Elliot) V1 Milling Machine
By andrew_mx83 in forum METALWORK FORUMReplies: 9Last Post: 29th September 2013, 11:49 PM -
Recycled Timber Machining Service Recommendations
By wynyard in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 3Last Post: 4th March 2012, 06:22 PM -
Milling a Silky Oak
By BobL in forum SMALL TIMBER MILLINGReplies: 30Last Post: 17th January 2012, 12:13 AM -
Free timber in Gippsland (near Traralgon)
By cuppa500 in forum TIMBERReplies: 3Last Post: 19th August 2009, 05:43 PM -
Need northern silky oak in Victoria
By busyhands in forum TIMBERReplies: 4Last Post: 24th May 2009, 10:24 AM