Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: Tips for new bandsaw millers
-
9th August 2022, 08:45 PM #1New Member
- Join Date
- Aug 2022
- Location
- Australia
- Posts
- 4
Tips for new bandsaw millers
Hi folks, I don't have any experience milling timber but I'm about to pick up my first wood mill and wondering if those of you with experience can recommend any good resources for a newbie to study. I'm in SE QLD and will be milling Iron bark with a Hardwood mills GT34 on a rural property we own.
I've watched the mill in operation at Toowoomba farm fest and have been shown how to sharpen the blades. Other than that Ive been watching a bunch of vids on YT.
Cheers,
Kelly Anne
-
9th August 2022 08:45 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
10th August 2022, 03:59 PM #2GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,567
Hi Kel and welcome to the Forum. Congrats on your purchase. Just a couple of suggestions; If there is somebody in your area with the same or similar mill it would be a good idea to spend a day with them to get the hang of it. Your supplier may be able to give you some leads. There is nothing more frustrating than having to reinvent the wheel when all you want to do is cut wood. Another point I would mention is your desire to attack Ironbark. Great timber when you know what you are doing but very unforgiving if you dont. If I were you I would be starting out on some lighter, less dense hardwoods to run both you and the mill in. A mill needs to be well tuned for the heavies otherwise the blade can snake or worse break. What else grows on your block?
-
10th August 2022, 05:23 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,831
I agree with Rustynail, try milling something softer at least for the first few logs. I tackled my first ironbark after milling about 50 other logs and even then still found it very difficult and frustrating. If I had tried milling it flrst up I reckon I would have given up and gone home.
-
11th August 2022, 09:05 AM #4New Member
- Join Date
- Aug 2022
- Location
- Australia
- Posts
- 4
G'day, thanks for the tips & welcome. I've got some grey gums on the property. Not sure which sub species they are but based on the advice I'll start with some of those. It'll be a little while, I've picked the mill up but still have the assembly to get done.
-
12th August 2022, 04:41 PM #5GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,567
I think you will find Greygum almost as difficult as Ironbark. Maybe keep your eye out for a pine log or two. Stringybark would be a good starter into hardwoods.
-
12th August 2022, 04:57 PM #6.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,831
What about a River Red gum (Camaldulensis)? I've only milled logs of the Camaldulensis hybrid with the WA Southern River gums. It's still hard but nothing like Ironbark. Here in WA we have a Eucalyptus/Bloodwood called Marri which is relatively soft so is a good tree to practice on. I also like milling your trees because the sap wood smell like Corona beer, older trees smell mustier and not so pleasant.
-
13th August 2022, 06:54 AM #7New Member
- Join Date
- Aug 2022
- Location
- Australia
- Posts
- 4
Yes there is pine scattered across the property but it is invariably small. I'll look for a workable specimen or two ... not really looking forwards to that, it's a bit of a PITA to get in, fell and clean up. The other species present is a plethora of equally small Bull Oak. I think my milling journey is going to be via the school of hard woods.
-
13th August 2022, 03:56 PM #8GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,567
Ok, here are a few tips for hard hardwoods: Make sure your blade is suitable and sharp. Correct blade tension. Check tension frequently(blade stopped.) Plenty of lubrication on blade (water) Keep the revs up. Slow feed. Buy or make a log peavey or cant hook (it will become your best friend.) Look after your back.
-
13th August 2022, 08:54 PM #9New Member
- Join Date
- Aug 2022
- Location
- Australia
- Posts
- 4
Thanks Rusty. I'll take those points on board. I don't have a cant hook yet but will weld one up before I finish putting the mill together.
-
14th August 2022, 12:09 AM #10Senior Member
- Join Date
- Jul 2018
- Location
- Canberra
- Age
- 67
- Posts
- 162
I mill on a GT26. Make sure you have the mill on a good solid bed, with a nice clear path for the operator. Pushing a mill uphill is not fun. We use 2.4m * 200mm * 75mm hardwood sleepers bolted onto concrete. It has made life much easier. Leave room to blow the sawdust and detritus away from the mill. Try to orient the mill so the operator is upwind most of the time. It saves having dust blown in your face.
Make yourself a parbuckle & loading ramps, or some similar system, for making loading logs easier.
A good cant hook is an absolute necessity for turning logs. If you can, make the handle from a good piece of 65mm sq hardwood, shaped with a draw knife and spoke shave. Wood is better on the hands in my opinion. We use 3x.
If you do any short stuff, under 1m, make yourself a false bed to bridge 2 bunks, and make up a couple of bits of 40mm RHS dogs and weld a support fence between them. It makes life easier.
Get a good 3/4 axe (and a debarking spud) for stripping off bark. Your blade will last much longer, especially on ironbark. Keep a wire brush handy for cleaning off mud & grit if there is any under the bark, same reason.
On the top of the guide pillow blocks, there are 2 channels to distribute the lube onto the blade. Make sure you don't put the pillow block on upside down... Use plenty of lube, water is cheap, and it makes a big difference.
The throttle cable will break. Keep a spare. The fixed guide_block holder assembly will probably break at some stage, as it gets hit by slabs fairly regularly. Keep a spare.
-
14th August 2022, 09:58 AM #11.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,831
Here's a photo of a couple I made a decade ago.
I can really recommend putting teeth on them like the smaller one
pair.jpg
DragonCloseup.jpg
The tree lopper boys in the yard have taken these out on site and have worked them super hard but they are still going.
Similar Threads
-
Horizontal Bandsaw Central - everything for Tips, Tricks and Mods
By MWF FEED in forum METALWORK FORUMReplies: 0Last Post: 28th March 2021, 05:30 PM -
Any tips for fitting dust extraction to an old bandsaw?
By RSD in forum DUST EXTRACTIONReplies: 9Last Post: 8th October 2020, 06:02 PM -
Maybe of interest to you millers
By Big Shed in forum SMALL TIMBER MILLINGReplies: 0Last Post: 30th March 2011, 06:52 PM -
Bandsaw millers
By comgreserv in forum SMALL TIMBER MILLINGReplies: 11Last Post: 10th September 2010, 10:47 PM -
Why are we mobile millers?
By Sigidi in forum SMALL TIMBER MILLINGReplies: 9Last Post: 7th September 2009, 09:19 AM