Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
Thread: Mini Solar Kiln
-
31st August 2012, 02:10 AM #1
Mini Solar Kiln
I decided to build a mini solar kiln primarilly to remove the last few percent MC in veneers or small pieces, basically it's just a box with some glass on the front.
It has turned out bigger than first imagined but the size was dictated by the existing shower screen doors (reclaimed from a bathroom reno) that I had stashed away for just such a use
open kiln.JPGclosed up.JPGAttachment 221658
There's some baffles and a fan baffle to go in still but it's about there, a quick test and it was 10° warmer inside than outside with the kiln pointed towards the end of the days rays
Pete
-
31st August 2012 02:10 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
2nd September 2012, 02:41 AM #2
Gave the kiln a real try today.....
Plenty of space for veneers, I lay the veneers with a slope so I get even airflow through the stack, made up some baffles to direct air flow, then closed it up and watched the temp rise, the day was bright sunshine, outside max temp of about 25°C and kiln got to about 48°C, veneers were about 17% and in about 5 hrs was down to 8%, I let things cool down from here, I'm not real sure which actual species the mango is but the MC comparison chart I have lists 3, it could have an actual MC of 7/11 or 8 so it should be close enough
plenty of room for veneers.JPGrear of stack.JPGairflow baffles.JPG
hot airflow baffles.JPGwith the glass front.JPG
Pete
-
9th September 2012, 12:26 AM #3
Pete
It look like an interesting set up. Have you considered including some insulation? Some polystyrene sheets and some alluminium foil over the top would be cheap enough.
What sort of fan will you use? I expect some thing very small would be quite sufficient. I think distributing the air over the whole kiln is the harder issue and in particular forcing the hotter air from the top back down to the bottom.
A charge of timber that doesn't occupy the whole kiln also presents problems as the air is reluctant to pass through the timber. It will always take the easiest path.
Having said all that, you had amazing success. I would not have expect the timber to dry that quickly. It must be because the material is so thin.
Excellent project. I can see people dismantling their showers all over Australia as we speak.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
9th September 2012, 01:48 AM #4
Hi Paul,
Insulation might happen at some point later, the fan is reclaimed out of an above the stove rangehood, it's two speed as well, a bit swisho, seems to be quite sufficient, to direct the airflow thru the stack I use baffles or boards to block off gaps.
From green to dry can be as little as 2 weeks for thin mat'l, the mango in this case only needed a little bit of drying so was all good
Pete
Similar Threads
-
Solar Kiln
By Chomers in forum TIMBERReplies: 12Last Post: 16th February 2011, 04:35 PM -
Solar kiln questions
By robduca in forum SMALL TIMBER MILLINGReplies: 2Last Post: 24th November 2009, 03:29 PM -
solar kiln
By paul bowers in forum WOODWORK - GENERALReplies: 6Last Post: 3rd February 2008, 09:44 PM -
Solar Kiln
By Beerbotboffin in forum TIMBERReplies: 17Last Post: 6th March 2007, 09:56 PM -
Solar kiln
By JB in forum TIMBERReplies: 25Last Post: 17th December 2004, 05:58 PM