Thread: Third Plane Blades for Wooden Hand Planes Batch Order

You do not owe anything. I will take your name of the list.

TS, Hi. Can I order the following:

Qty 2 - 50 x 4 x 100 mm
Qty 1 - 50 x 6 x 100 mm

Mark

Hi Mark - I have added you to the list.

I have also attached the latest PDF.

Hi Helmut,

Can you please change my order to:

2 @ 60 x 6 x 100

instead of the 50mm blades

Thanks,
Will

Done

Originally Posted by Willard

Hi Helmut,

Can you please change my order to:

2 @ 60 x 6 x 100

instead of the 50mm blades

Thanks,
Will

Confirming my order, one 40 x 4 x 150mm blade

thanks

Neil

Hi TS
could I please order

one 50 x 6 x 200 mm
one 60 x 6 x 200 mm

Total cost ca. $120

thanks and keep up the great work
cheers
jackaranda

Originally Posted by thumbsucker

I have been getting PM's from members asking me to run another batch order for wooden hand planes. So here we go again.

The steel will be M2, the blade thickness will be 4 mm or 6 mm in a wide variety, widths, and lengths, to suit virtually every need.

Here are the size, thicknesses, and prices, that will be on offer.

• 25 x 4 x 80 mm @ $41.00
• 30 x 4 x 80 mm @ $41.00

• 40 x 4 x 50 mm @ $41.00
• 40 x 4 x 100 mm @ $43.00
• 40 x 4 x 150 mm @ $46.00
• 40 x 4 x 200 mm @ $49.00

• 50 x 4 x 60 mm @ $41.00
• 50 x 4 x 100 mm @ $43.00
• 50 x 4 x 150 mm @ $46.00
• 50 x 4 x 200 mm @ $49.00

• 50 x 6 x 100 mm @ $48.00
• 50 x 6 x 150 mm @ $53.00
• 50 x 6 x 200 mm @ $58.00

• 60 x 6 x 100 mm @ $50.00
• 60 x 6 x 150 mm @ $56.00
• 60 x 6 x 200 mm @ $62.00

Per usual the steel will come from Bohler in Melbourne. The heat treating will be by Sutton Tools, and the milling and grinding will be done by Alco. The blades will be laser cut from a sheet, using the same tombstone theme used for the Stanley Plane Blades.

I have over estimated the cost, based on previous cost's we had for them in the past, plus a safety margin, so the price will be very stable.

Attached is the usual pdf's.

The ETA for this order is three months. I do not want it to drag on for to long. So get your allocation in as soon as possible.

Hi TS

Is there any reason why you are not offering 40 x 6mm blades in various lengths?

Perhaps, if there were only one or two of that size blades in the batch that would not allow for the optimum use of the M2 sheet. If that is the case, I would be happy to pay the extra for 50 x 6mm if I could have it laser cut to yield two pieces: 40 x 6mm and 6 x whatever width remained from 50mm after the laser cut. I can always make good use of the 'off-cut'.

However, if this is all just too much extra trouble I can fully understand....

Neil

Neil if that is a size that interest you, I can add it in.

What length would you like?

Originally Posted by thumbsucker

Neil if that is a size that interest you, I can add it in.

What length would you like?

Thanks TS.

In that case I will change my order from 1 @ 40 x 4 x 150mm to 1 @ 40 x 6 x 150mm.

Regards

Neil

Originally Posted by bordo

TS, Hi. Can I order the following:

Qty 2 - 50 x 4 x 100 mm
Qty 1 - 50 x 6 x 100 mm

Mark

TS,

Hi. Can I change my order to:

Qty 1 - 40 x 4 x 100 mm
Qty 2 - 50 x 6 x 100 mm

Mark

Mark I have updated your order.

TS
I'm in too.

Can you put me down for:
2 No 50 x 4 x 100
4 No 50 x 6 x 100
2 No 40 x 4 x 80

Kapex

G'day Helmut,

I was just reviewing the spreadsheet and I believe my order isn't correct. Would you mind reviewing this as per my first post in the thread?

Thanks Helmut.

P.S. Will this batch get underway following completion of the current chisels batch order?