Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 24
-
28th December 2008, 12:55 PM #1Intermediate Member
- Join Date
- Jan 2007
- Location
- Brisbane
- Posts
- 25
can this rusty old trailer be salvaged?
Gday.
I bought this 6x4 terror off ebay
Just wondering if you guys reckon its salvagable.
I managed to take 2 photos before my camera ran out of batteries, so if you think I should take some more I can in a couple of hours.
The photo of the rusted trailer floor shows where the cut frame is poking through the floor which is the only support for the front of the suspension. (if i push down on the trailer that small block midway on the picture goes further up through the floor)
The side photo shows the missing section of frame supporting the above mentioned front attatchment for the suspension.
Seeing as its quite rusty,(ignoring the floor.... for the moment) Could getting a bar welded to replace the missing section of frame solve some of the structural problems? or is this not worth it.
-
28th December 2008 12:55 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
28th December 2008, 02:26 PM #2
Tut, tut...
The perils of buying off ebay.
The two things that will determine whether it's worth fixing are; How much you paid for it, and how much work you can do yourself.
For me, fixing that is a "no-brainer", but it would require a fair bit of labour, and would be worth more than a new trailer if you were to pay someone to fix it.
My concern would be fixing it properly too. The last thing I want as a fellow road user, is a fully loaded trailer heading towards me and my family at 100km/h, minus its drawbar.
I would remove the floor completely, and see what other rust is in the chassis. If the rest of the sheetmetal is OK, you could make a new chassis, and use the old axle, springs, sides, guards, tailgates and coupling, and put a new floor in.
If the picture you show is the only major damage, you could just replace that one side rail, and then the floor.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds! Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
28th December 2008, 02:39 PM #3
-
28th December 2008, 06:05 PM #4
I'd also have a serious look at how well the trailer is tracking now (including backing) and test how it balances when unhitched with a load.
'Cos if you do need/decide to rebuild the chassis, this'd be the best time to make any changes to axle positioning and rebuild it better than the original.
- Andy Mc
-
28th December 2008, 07:03 PM #5
If that is the state of the floor and frame, what are the springs and axle like? Hope you didn't pay too much for it.
I have a 6x4 with 1200 removeable sides and canopy for sale for $150 at the moment, it may need tyres and a new floor, but at least it is not as bad as that one.Neil____________________________________________Every day presents an opportunity to learn something new
-
29th December 2008, 12:27 AM #6Intermediate Member
- Join Date
- Jan 2007
- Location
- Brisbane
- Posts
- 25
[quote=Yonnee;868354]Tut, tut...
The two things that determine whether it's worth fixing:
1. too much.. I paid 360 (once paypal generously gave an xmas discount). (link if ur interested) There were plenty cheaper in the trading post, but by the time u call up 2 hrs after its been published about 20 000 people have already called before you. It did however come with some nice wheels + a spare + a jockey wheel + rego...
2. Fixing would require all of my brain cells. The most welding i've done is behind my computer watching youtube how-to videos over the last few days. However I am not scared to tinker..buying equipment would be out of the question though so hiring equipment or someones services would be my only 2 options. Maybe bunnings leases stuff.... That option sounds like alot of reading.
I'm thinking of ripping up the floor as you say and seeing whats under. From what I can tell the left side rail for the chassis is wrecked. the other side looks to be in one peice although there is rust damage around the edges of everything to a lesser extent.
The other option is to resell it I guess and try again.
sensai if you have rego and the frames good u shouldn't have too much trouble selling it.
Chidman, seeing as the left suspension is poking through the floor slightly, I think the trailer is probably sitting slightly lower on that side.
-
29th December 2008, 12:51 AM #7SENIOR MEMBER
- Join Date
- Oct 2008
- Location
- Perth
- Posts
- 966
The stub axles, springs, frame and hitch are worth saving. Bodies are relatively cheap and can be bent up for you at any trailer place.
Go for a galvanised body this time, and it will last you near on forever.
-
29th December 2008, 11:39 AM #8
mmmm I found an old 10x5 trailer at the tip yesty with a similar fault... only from what the bloke dropping it there said he drove his tractor over the drawbar!! yep both sides broken through and holding to the frame by a mere couple of centremeters of metal... but the rest appeared okay wooden floor but... anyway as I only had my 8x5 trailer with the 4ft high cage with me and he wasnt happy about my idea of him putting it back on his truck and bringing it here for me to fix... its still sitting at the tip
But I think it would have been an easy fix just cut of the existing drawbar peices hold onto the hitch and other stuff and rebuild the drawbar replace the floor with the sheets of steel I nicked from somewhere or other and bobs yer uncle!
Mate I reckon you should charge those camera batteries and start crawling around under and around it taking copious amounts of snaps and then upload them to here so Yon Young Yonnee and others can give yer words of advice on how best to fix her up... cause fixable she be from what youve given
Cheers
ShaneBelieve me there IS life beyond marriage!!! Relax breathe and smile learn to laugh again from the heart so it reaches the eyes!!
-
29th December 2008, 12:05 PM #9
-
29th December 2008, 03:16 PM #10Old Chippy
- Join Date
- Mar 2007
- Location
- Canberra
- Age
- 72
- Posts
- 394
I'd be putting it back on ebay and seeing if you can find another person like you. IMO you paid too much and the effort to fix given what you describe are your skills and tools (ie: few) any effort you put in or pay for would be way more than it is worth.
-
1st January 2009, 10:21 AM #11
Attachment 92885
This pic would have rung the alarm bells for me...
Unfortunately, I you did pay a bit much for it. If you can't do alot yourself, it'll be one expensive trailer when you've finished.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds! Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
1st January 2009, 06:05 PM #12Intermediate Member
- Join Date
- Jan 2007
- Location
- Brisbane
- Posts
- 25
yes it turns out i'm a doofus.
Guess what I've been up to on new years day. See attached pictures.
I attacked the trailer with my heavy machinery (axe and shovel.... )
There is a welder around the corner from where I live I might drag this roadunworthy beast down there and get him to tell me that its not worth it.
Anyway have a look at my pics and point and laugh
.
-
1st January 2009, 06:15 PM #13
Oh dear!
If you were one of our metalworking brethren (ie had the tools, time & inclination) you could still get a reasonably priced trailer out of it by salvaging the guards, hitch, axle, etc.
But paying someone else to do it...
Bummer!
- Andy Mc
-
1st January 2009, 08:21 PM #14
I don't think its that big a boo boo. People looking to build a trailer would have paid around that for the bits and pieces. Trailers have become so expensive.
Why don't you just give it a go? Remember, it's not all loss when you develop skills and buy tools and materials to do these things yourself. You have the tools, left over materials and some new skills for the next project. Strip that thing down completely and de-rust the good bits and rebuild the bad bits and put it together. Just take your time.
I have a similar project waiting for me.
-
1st January 2009, 08:27 PM #15
Good start, now you can easily work on the rotted sections.
I've got another trailer lined up that I'll do exactly the same thing on.
Similar Threads
-
Salvaged Parts
By Black Ned in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 5Last Post: 3rd July 2008, 10:04 PM -
Salvaged for Pens
By Black Ned in forum WOODTURNING - PEN TURNINGReplies: 17Last Post: 30th June 2008, 11:36 PM -
Pine table salvaged
By Scally in forum WOODWORK PICSReplies: 7Last Post: 25th August 2007, 12:46 PM -
Salvaged Tassie Timber
By m2c1Iw in forum Links to: TIMBER & HARDWARE SUPPPLIERSReplies: 4Last Post: 1st July 2007, 10:15 PM -
salvaged timber
By wajor in forum WOODWORK - GENERALReplies: 7Last Post: 8th December 2004, 02:18 PM