Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: CARBI-TOOL 3D ROUTER
-
6th June 2014, 08:12 PM #1
CARBI-TOOL 3D ROUTER
I have just been on a "tour" in the land of the internet, you know how it works-click here end up there then round and round.....You get the message.
A question came to mind, as I was surfing, and that was has anyone got any experience with this Carving System? I have known it to have been around for years (20?). I have never seen or heard anyone report its use. As I said I was just wondering. Also any one got any idea of price? Carbi-Tool's cattle dog didn't show itJust do it!
Kind regards Rod
-
6th June 2014 08:12 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
6th June 2014, 09:58 PM #2
Hi,
Check this thread out https://www.woodworkforums.com/f88/3d-carb-tool-router-carver-129596.
As my post says I like them. They have (or had) their own catalogue.
RegardsHugh
Enough is enough, more than enough is too much.
-
7th June 2014, 10:14 AM #3
Hi Hugh
Thanks for the reply. Can you remember what you paid for your set? (a rough idea would be good) I am a little surprised that you don't see more of them about on finished work. I know you probably wouldn't use them on every job but I really can't remember seeing any body on this Forum using them.Just do it!
Kind regards Rod
-
7th June 2014, 04:18 PM #4
Hi,
I got my original lot from the now de-funked Jasada in about 2008 and built up my collection.
I don't seem to have posted much showing any, but some can be seen on this piece https://www.woodworkforums.com/f40/ladys-table-124801
RegardsHugh
Enough is enough, more than enough is too much.
-
7th June 2014, 04:59 PM #5
Thanks for that Hugh. I do like the subtlety of the carving. Its there but not "in your face". I think that with the inclusion of any of the carvings adds a bit of interest to the whole job
Just do it!
Kind regards Rod
-
10th June 2014, 09:00 PM #6
Never seen them in person, but episode 1 of Stus Shed video podcast is a 15 minute discussion/demo of them. May be useful if like me you haven't seen them in use, or alternatively might be a crock for you, but the programme is out there somewhere.
I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
Similar Threads
-
3D Carb I Tool router carver
By jenno in forum ROUTER JIGSReplies: 8Last Post: 14th January 2011, 12:16 AM -
Tool/Router advice
By tim290280 in forum MUSICAL INSTRUMENTSReplies: 18Last Post: 17th January 2009, 01:16 PM -
Jet or Carbi-tech bandsaw
By Paul B in forum BANDSAWSReplies: 18Last Post: 20th October 2005, 11:54 PM -
Carbi tool Router Bits "Difference"
By HarryM in forum ROUTING FORUMReplies: 17Last Post: 11th October 2005, 01:46 PM -
Carb-I-Tool Router bits
By Mark Woodward in forum HAND TOOLS - POWEREDReplies: 4Last Post: 18th November 1999, 08:37 AM