Needs Pictures: 0
Results 46 to 60 of 113
Thread: Rob Roy
-
3rd March 2022, 03:16 AM #46
Due to other jobs not a lot on the loco but have managed to fix some parts together I know not a lot to look at.
I started by drilling 6 holes in each of the angle brackets and then riveted these to the buffer beams on the outside the rivets disappeared (well nearly just make out one of them) with a little draw filling and some wet and dry paper I have not brought these to a exceptional finish as I want a little roughness for the paint to adhere to so only done to 240 grit. Surprising how long this all took now to do the other end which the angle brackets are larger but only have 4 rivets in each.
DSCF2260.jpgDSCF2262.jpg
-
3rd March 2022 03:16 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd March 2022, 08:14 PM #47
You have started a big project. Only by taking little steps will it get finished. Somedays there will be nothing to show for an hours work, other days it will appear a lot has been done.
Marking out and setting up takes time, but will appear that nothing has been done, but if it is not done accurately it will show.
Thank you for posting your progress.
-
4th March 2022, 06:05 AM #48
So true. Like today I spent most of the day sowing seeds in the greenhouse after a visit to the garden centre, had to handcuff the wife to stop her buying flowers for the garden as it is too early in the year for them just brought vegetables.
Then a parcel arrived full of various castings for the loco, I did manage a little more time this time on the rear buffer beam angle brackets which I have drilled the four holes in each ready for them to be riveted to the beam
-
9th March 2022, 05:19 AM #49
Other than workshop time I seem to be spending a lot of time in the garden preparing for the nice warm weather and growing season.
Anyway workshop time has had some time. Completed the second buffer beam rivets, picture with both you will notice that the rear on has only 4 rivets per angle bracket not sure why but that is what the plan calls for.
Also one of the horn blocks machined and test fitted very pleased with the fit no slop but just slides in that will need cutting in half and riveted in place now to do the other two.
DSCF2269 (2).jpgDSCF2268 (2).jpgDSCF2267 (2).jpgDSCF2266.jpg
-
9th March 2022, 06:41 AM #50Senior Member
- Join Date
- Jan 2019
- Location
- Christchurch New Zealand
- Age
- 81
- Posts
- 307
Looking good unfortunately life jobs get in the way at times.
-
9th March 2022, 07:59 AM #51
-
11th March 2022, 09:06 AM #52GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,432
Keep up the good work Derek
-
11th March 2022, 09:31 AM #53SENIOR MEMBER
- Join Date
- Sep 2010
- Location
- Port Sorell, Tasmania
- Posts
- 595
-
17th March 2022, 06:14 AM #54
At last the main horns are completed except for the rivet holes which have been marked. I was a little worried when I started them but soon got into doing them after many measurements taken and calculations checked double checked and even triple checked before a cutter touch the metal.
All three sets fit nicely into the frames now it is a case of drill the holes in them and the frames ready for riveting. I am happy with how they turned out, the inner corners will be filed square once they are fitted.
As can be seen in the photo they are still joined, that is why there is a gap at the top.
Getting closer to the first major assembly of the chassis
DSCF2282 (2).jpg
-
21st March 2022, 04:50 AM #55
I finally got the main hornblock frames riveted into the side frames that was 7 rivets for each one and six to do. I need to set them up in the mill to cut back the blocks so they sit flush with the bottom of the frame as can be seen in photo 2 they are sticking up
DSCF2283 (2).jpgDSCF2287.jpg
I also turned two bushes for the weighshaft which needed to be a press fit, the first one I did was just a fraction to loose so had to start again but got there in the end which was annoying as it was only 0.001" too small.
DSCF2286.jpgDSCF2285.jpgDSCF2284.jpg
-
29th March 2022, 08:35 AM #56
Yet more gardening had to plant three roses that the wife got for mothers day more blood drawn doing those than when metalworking at least the garden is starting to look nice but a lot still to do like transplanting seedlings and final prep of the veg patch.
Anyway some more progress on the loco Cut a block of gunmetal into a long axle box shape (not shown) then it was a case of cutting this into six 1" long pieces. Test fitted into the horns with a very little fettling they all slide nicely each one was numbered as well as the horns to keep them in the right order.
DSCF2291 (2).jpgDSCF2293.jpgDSCF2294.jpg
Set up the vice on the mill with a stop which helped set up time for each of the axle boxes which were drilled and reamed for the axles, then another set up to drill two holes in each for the springs. You can see the numbers on the boxes and on some of the horns matching each together this was done so the numbers are on the inside of the chassis and will not show on the completed model
DSCF2305.jpgDSCF2307.jpgDSCF2303.jpg
Getting very close to the chassis assembly still need to make the springs and the horn stays
-
29th March 2022, 02:48 PM #57Senior Member
- Join Date
- Jan 2019
- Location
- Christchurch New Zealand
- Age
- 81
- Posts
- 307
Looking good I am not a good metal worker.
-
1st April 2022, 01:35 AM #58
-
3rd April 2022, 03:48 AM #59
Six Hornstays made and drilled then the horns drilled and tapped followed by shortening the fixing screws as I only had some which were too long these are 5BA bolts
DSCF2319 (2).jpg
The centre support rod was cut and drilled either end then tapped 6BA so I took the opportunity to do a dry fit. Hopefully will be able to get the surface plate out and get everything squared up and the holes drilled and tapped to hold the buffer beams in.
DSCF2316.jpg
-
4th April 2022, 11:18 PM #60
Time to drill the last holes ready for assembly first job was to set the frame on my surface plate had to do this across the diagonals and add a steel bar of the correct diameter to bring the frames in a level plane check no rocking I also checked the buffer beam also sat correct across the frames as well as insert a silver steel axle (well it will be the axle when cut and turned) this was to check that it was at right angles to the main frames.
This went quite well and did not take long which was a relief clamped the buffer beams to hold every thing in place
DSCF2332.jpg
Now it was assembled the holes in the buffer beams was marked through the frames and one of them was removed to drill all the way through. Only just managed to drill some of the holes as the drill bit was just a little short to do all of them.
I also found out that my 6BA tap was too short so could not tap the holes. I do have some long series taps but not the one needed so now have to wait for one to be delivered. Hopefully today I will get the other end drilled and tapped as it need a different size which I have and that is 5BA
DSCF2331.jpgDSCF2330.jpgDSCF2328.jpg