Needs Pictures: 0
Results 76 to 90 of 175
-
24th September 2014, 09:42 PM #76
-
24th September 2014 09:42 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
24th September 2014, 09:45 PM #77
To me these sound high. I thought the Triton had a max speed of 22000 rpm, so I did I quick search and according to their web site it is 20000 rpm. Could have been changed since I purchased my router.
One rule of thumb or at least a loose guideline is larger bits slower speed and smaller bits higher speed. This rule does not take into account how hard/fast you push wood through the router.
-
24th September 2014, 09:57 PM #78
-
24th September 2014, 10:03 PM #79
I am not an expert with the router but I find it is one of the most enjoyable electric tools. I only have one and most of the time it is mounted in the table. For small repetitive jobs it is a very accurate once the fence and guide is setup.
When I use this out of the table it can be a little tricky and time consuming to setup but once everything is setup and secure it gives a good result.
I normally take small shallow cuts(2-3mm) when using smaller bits and a little deeper(5-6mm) when larger diameter bits are used. I have tried it a little deeper to test the limits and generally find some equilibrium.
Of course there is another choice / option.
-
24th September 2014, 10:06 PM #80
-
24th September 2014, 10:12 PM #81
-
24th September 2014, 10:21 PM #82
I guess it's an option.
I went over the road to the routing forum to ask the question so that may provide some options as well.
-
24th September 2014, 10:31 PM #83
If it is one pass like a channel then I would agree, but this is hogging out material and you have a tendency to jump depending if you are doing a climb cut when hogging the material out. That being said I have hogged out material with the router in the table but this is between two stops and the fence. The final pass was only 1mm and avoided the climb cut.
-
24th September 2014, 10:44 PM #84
-
25th September 2014, 11:05 PM #85
You are better off with multiple 1/4" passes for the depth than trying it all in one go. Start off with a central dado.
Then take it gradually to the edges, leaving a final pass of about 1-2mm.
That's how I did mine (no routing details, I'm afraid) ... http://www.inthewoodshop.com/ShopMad...ngaBench2.html
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
25th September 2014, 11:34 PM #86
Your photo of your router on the blog appears not to have a template guide insitu. Is that a template bit in the collet?
-
8th November 2014, 03:36 PM #87
So after a steep learning curve the dog strip is glued on.
image.jpg
-
8th November 2014, 03:42 PM #88
Well done Paul... ...
-
8th November 2014, 03:50 PM #89
Absolutely luvverly......but you should lose points for having matching clamps
flettya rock is an obsolete tool ......... until you don’t have a hammer!
-
8th November 2014, 04:43 PM #90
Paul its looking tops
Similar Threads
-
Roubo Bench Issues and Questions
By derekcohen in forum THE WORK BENCHReplies: 244Last Post: 31st March 2012, 11:30 PM -
Underhill's Roubo bench
By The Pom in forum THE WORK BENCHReplies: 4Last Post: 14th June 2011, 11:57 AM -
Dan's Blackbutt Roubo Bench
By BozInOz in forum THE WORK BENCHReplies: 215Last Post: 8th April 2011, 08:21 PM -
WIP Roubo bench
By mic-d in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 48Last Post: 30th January 2009, 04:34 PM -
A mans wish
By Gino in forum WOODIES JOKESReplies: 2Last Post: 1st October 2002, 12:21 AM