Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: pick ya brains
-
15th October 2008, 08:16 PM #1GOLD MEMBER
- Join Date
- Sep 2008
- Location
- texas, queensland
- Posts
- 1,239
pick ya brains
G,day just throwing this in to see if there are any good ideas .
my bandsaw is a very old very heavy cast iron 3 phase "BERRY"S SUPER " which is an old butcher shop meat saw .
the wheels are cast and they dont have a rubber coating where the blade runs , the blade runs straight on the domed steel .
and i think this is taking some of the set off the teeth of the blade i am looking for ways of rubber coating the wheels ?????????
the wheels are 17 inch diameter and about an 1 1/4 wide .
have thought of the rim tapes that go in push bike wheels but they are not very thick,
also thought of slicing a ring from a large tractor tube and stretching it over the wheel but there is not recess to hold it there , though if it tight it may stay put .
anyone got any clue's
-
15th October 2008 08:16 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th October 2008, 09:52 PM #2
I've seen discussion about and/or ads for replacing the rubber tires on bandsaws
have you tried a google search ?
ian
-
16th October 2008, 04:58 AM #3
Hey texx,
meat cutting bandsaws were designed to be hosed out and cleaned everyday, hence no rubber,
if there is enough metal on the wheel rim its easy enough to take them to a machine shop and have them turn a recess for you, should be a quick job and not cost too much
what if the hokey pokey is really what it's all about?
-
16th October 2008, 07:48 AM #4GOLD MEMBER
- Join Date
- Sep 2008
- Location
- texas, queensland
- Posts
- 1,239
yeah there probably is enough there to get a slight recess machined into it .
but i dont think there is such a thing as a cheap machining these days .
i have found some stuff on gluing inner tube rubber on the wheels since i started this thread might try that first
-
16th October 2008, 10:16 AM #5
-
16th October 2008, 05:45 PM #6GOLD MEMBER
- Join Date
- Sep 2008
- Location
- texas, queensland
- Posts
- 1,239
yeah i know they need a domed pulley thats what keep's em on , same as the flat belt pto pulley on my tractors.
and thats a good reason not to machine the pulley i think i will just try and glue some rubber on it
-
17th October 2008, 12:15 PM #7Member
- Join Date
- Jan 2008
- Location
- Adelaide, South Australia
- Posts
- 90
Hi Texx,
take care of what thickness of rubber you are planning to glue on as this increases the diameter of your wheels. The blade will be in a slightly wider position in the table insert and unless your top and bottom blade guides have sufficient side movement, correct adjustment might be difficult or impossible.
A new machine from Santa might be the other answer.
Cheers
Edwards
-
17th October 2008, 07:03 PM #8GOLD MEMBER
- Join Date
- Sep 2008
- Location
- texas, queensland
- Posts
- 1,239
yep thanks never thought of the blade guides.
and santa wont be coming anywhere near me im afraid
-
17th October 2008, 11:06 PM #9
Gluing a cut-up inner tube to the existing wheel should only move the blade over a couple off mm at worst. It's not like you're gluing on a cm thick tyre or something.
If your insert or guides can't handle that little deviation... [shudder]
Assuming the blade runs centred on the crown of the dome then it shouldn't be taking the set off your blades - unless the set of the teeth is greater than the curvature of the dome or the blade is over-tensioned to the blazes. I'm wondering what sort of set meat-blades have, if any?
Regardless of "shoulds" & "should nots," I'd do as you plan and glue on a section of inner tube. If, after running it on rubber for an hour or two, you inspect the rubbers and see gouging where the teeth are chewing out the rubber then you'll know that your suspicions of it flattening the set are correct.
If so, this is also correctable with a little effort. (eg. removing the rubber, gluing on a 1/2" wide strip along the crown and then replacing the rubber.) But knowing it's a problem is one step further along the line than suspecting you have a problem.
FWIW, I reckon you're on the right path.
- Andy Mc
Similar Threads
-
Brains Trust, help needed with ROS
By ozwinner in forum WOODWORK - GENERALReplies: 12Last Post: 7th February 2007, 01:32 AM -
Im gonna try to tap your brains here!
By Wild Dingo in forum HAND TOOLS - POWEREDReplies: 13Last Post: 2nd February 2007, 07:35 PM -
Wood for brains
By bitingmidge in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 7Last Post: 5th June 2006, 11:19 PM -
Picking your brains!
By Handyann in forum FINISHINGReplies: 23Last Post: 14th October 2004, 09:07 AM -
Picking Brains ?
By Different in forum WOODWORK - GENERALReplies: 22Last Post: 24th July 2004, 06:01 PM