Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
-
7th August 2013, 04:33 PM #1Novice
- Join Date
- Oct 2012
- Location
- Rural WA
- Posts
- 13
How dry before repairing a Mirror, and are cheap moisture meters useful?
Hi,
I have a Mirror dinghy that I am stripping back and refinishing (previous owner = bodge repairs and shiney new paint that was peeling off solid old paint). It is generally very dry and rot free and it has been out the water for at least 18months but when I peeled the paint off I found a few small damp areas and one repair to a hole that water ran out of when stripped back (wish I had stripped it back 18 months ago then let it breathe...)
As I understand it I need it to be around <10% moisture content before attempting to get paint or epoxy to stick to it, is that correct? I have no idea what 10% looks like vs 20% etc so are any of the cheap moisture meters on ebay any good?
I am looking at range from really cheap ($12): NEW 4 PIN Digital LCD Display Wood Moisture Meter Damp Detector Tester | eBay
But I am wondering if those probes are a bit far apart as some of the dampe spots are quite small
Thru to $37 for inductive Digital NON Destructive Inductive Moisture Meter 4 Modes 0 40°C LED | eBay
Or do I just need to put a spotlight or heater on each small spot for a day or two and if it looks and feel dry then go for it? The wood is not soft or rotten, just wet in small isolated places
Thanks
-
7th August 2013 04:33 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
7th August 2013, 05:06 PM #2
Moisture meters can be helpful on large areas, but for small spots they're about useless. A 100 watt bulb with a shield a few inches away for a few days will easily dry out a small spot, so it can be painted. Once you remove the lamp, let the boat sit for a day so the moisture content in the area, can stabilize with the surrounding areas. An alcohol wash can expedite the process, so can acetone, which is faster. If it was me, depending on how wet it seems, I'd use a heat gun, then I'd draw out as much as I could with a few good soaking of acetone, more heat gun time, then a flood light on it for a few days.
-
7th August 2013, 06:39 PM #3Novice
- Join Date
- Oct 2012
- Location
- Rural WA
- Posts
- 13
I would never have thought of the acetone wash, great idea!
Will try that and the spotlight.
Thanks!
-
7th August 2013, 07:34 PM #4Banned
- Join Date
- Jul 2013
- Location
- Perth
- Posts
- 665
A surveyor
A vessel surveyor would use one of these.
Tramex - Non-Invasive Moisture Meters: Fast, Efficient and Hassle-Free - Moisture Meters, Moisture Detectors, Concrete Moisture Meters, Humidity Meters
They are surprisingly accurate in my experience...
-
10th August 2013, 11:05 PM #5
The light box idea is great to dry a small area around the defect, and yes leave it a couple of days to stabilize, do not get too tied up in 10% -20% moisture content, if it is dry to touch and you have used a heat source to dry the affected area, then the glue /resin will stick .
clean the defect and ensure that there is no dust or contamination in the area, then apply your resin/glue.
VK4.
Similar Threads
-
How necessary are moisture meters
By Karl Robbers in forum SMALL TIMBER MILLINGReplies: 26Last Post: 30th November 2010, 09:01 PM -
moisture meters
By mrtayls in forum WOODWORK - GENERALReplies: 7Last Post: 28th September 2010, 11:08 AM -
Moisture Meters.............Yes Again.
By outback in forum HAND TOOLS - POWEREDReplies: 16Last Post: 9th July 2005, 05:14 PM -
Moisture Meters
By peter_j_h in forum HAND TOOLS - POWEREDReplies: 2Last Post: 26th September 2001, 06:25 PM -
Moisture Meters?
By John Saxton in forum TIMBERReplies: 7Last Post: 14th September 2000, 09:57 PM