Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 46 to 60 of 97
Thread: New member of the Domino club!
-
25th August 2006, 09:06 PM #46Originally Posted by Lignum
-
25th August 2006 09:06 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
25th August 2006, 10:18 PM #47
The Studomiter
Originally Posted by Lignum
Like the adaption you have done with it as well."Clear, Ease Springs"
www.Stu's Shed.com
-
26th August 2006, 10:36 PM #48
Update on Incra LS-17 (and some Domi stuff)
Due to some other customer having a delay in his plans, Grahame was able to deliver an LS-17 and w/fence today. No charge for delivery - so we had a short shop tour in lieu I'll post some pics tomorrow as the gear is almost installed. I'll say again, Grahame is a top bloke to deal with. (Anyone else wanting some Incra gear: get in quick as there is a fairly big price increase hitting the stuff on, I believe, 1 Sept. Speak to Grahame...)
BTW, after the glue had set overnight on the Domi'd extension to the router table top it was rock solid and absolutely level. I have put under it a steel support bracket, but that's probably the braces to go with the belt Incra's lead screw mechanism and the fence just glides over the surface - and has a very easily repeatable .001" level of accuracy. Ok that's the fence part, the trick will be getting the Bassoon part up to speed :eek:
Faffing around this morning, I finished off the much needed new top for my Fwumping bench - just some Tas.Oak to frame the top and some inset Masonite. The job made much easier and faster with the aid of a few strategically placed Domis - plus a few DomiDogs (TM Lignum). I had to sand the Domis a bit in order to be able to insert and retract them - ordinarily the fit is a friction one, and makes the "loose tenons" a real stuggle to get out once inserted (danger of multiple hernias here :eek: ). I also took the opportunity to make up a new Beech outer vice face - with a couple of Domi clamping blocks
I'm sorry that the pics aren't that crash hot as I'd just applied some uBeaut wax to the Masonite to help seal it, and it's a bit shiny.
Three-way mitred/domi'd joint exercise to follow (and a wee Domi'd mitre joint for the person who asked for one).
Next up is to get the blerry great load of Blackwood into the shed (from A. Lewis & Co) for the current commission and get the Bassoon's ##### into gear and start making stuff . This is going to be so much easier with the Mistress . For those that have one, don't you just love the precision of the tool?
See ya!
-
26th August 2006, 10:46 PM #49Senior Member
- Join Date
- Apr 2005
- Location
- brussels
- Posts
- 128
Yes we do love the precision of The Tool. Thanks for yr enthusiasm.
riri
-
26th August 2006, 11:16 PM #50Originally Posted by Flowboy
As a w/end warrior, and much as I love (already!) my Domino, I find that for the relatively small amount of sanding that I do my Blue Bosch 125mm ROS is fine. After all, I do have an 850mm wide drum sander . Seriously though, most of my finishing work is with hand planes (like a Spiers replica or even an LN ) and/or with scrapers.
I am tempted, though, by the new cordless drill (around $600), but what gives me the eebie jeebies is that the systainer with the bits, etc is about the same again. Cor!
BTW, I've rigged up a means of connecting Domi to my shopvac, and this works just fine.
-
27th August 2006, 02:02 AM #51.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Originally Posted by Auld Bassoon
Originally Posted by Auld Bassoon
I hardly use my ROS now because Domi is so accurate.
Steve just wait until you do your first large panel or table top, you will spin out when you find you only have to scrape the glue off and give it the lightests of touch ups. Gone are the days when a S&!t load of planing and sanding are needed on a panel or table top.
And somewhere way back buried in the Domi threads i said the Domi is a "Darksiders Powertool" and its PERFECT partner is a LN or LV smoother and a few months after saying that im more convinced now than ever
-
27th August 2006, 07:00 AM #52Banned
- Join Date
- Jun 2005
- Location
- Earth, occasionally
- Posts
- 886
Hi Steve and Herr Doktor Lignum ,
Steve, I have the C12 and all accoutriments that go with it. Total Cost $840 with two 3 hour batteries and charger. The two countersinks, (which are great) cost about $150 total. I gave my opinion in the "My C12" thread and it just continues to impress. So comfortable and easy to manipulate in tight situations.
Lignum, I don't normally use a ROS to level up timber before or after joining, (I use LN smoothers, #4 and low angle and #6 foreplane for this) but do use it for friction sealing the oils I use. This still requires sufficient power and long periods of sanding at high grit values. I am indeed looking forward to using the domino on some long panels and will have the chance as soon as I can get these bloody chairs to the Upholsterer (this week I believe.) I've chosen the fabric BTW, a NZ wool, dark blue with some reddish counterpoints throughout. Sounds weird, looks good.
Regards and have a great Sunday all,
Rob.
-
27th August 2006, 02:32 PM #53.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Originally Posted by Rocker
Its very easy to see through the hole to align it accuratly to get the desired spacing, and the distance between the red lines is the same as between the retractable pins to keep it perfectly aligned.
Running some good masking tape along the edges and pressing it in firmly will stop any tear-out.
It would also be easy to have the fence angled to have the simulated dovetail look
-
27th August 2006, 03:05 PM #54
Lignum,
Great jig! But I am not sure whether joining the dots isn't overkill.
Rocker
-
27th August 2006, 03:26 PM #55
I think I agree with Rocker, the jig would be great for creating a simple spline look - that look works better for me.
-
27th August 2006, 03:34 PM #56.
- Join Date
- Jul 2005
- Location
- Victoria
- Posts
- 5,215
Interesting though in the flesh the tas-oak is similar to the domino and it is very subtle and looks good, but i would never use a stronger timber as that would be over kill
But the original reason in doing it is more to push and explore just what Domi is capable of. We are only just finding our way with her and as time rolls on the uses will just keep on increasing.
-
27th August 2006, 04:38 PM #57
Go for it Lignum!
-
27th August 2006, 10:39 PM #58
Today I cut, milled and jointed some of the Blackwood for the Server (1st piece of current commission).
After a run through the jointer and a swoosh or two with a hand plane, I marked out a few Domi lines and Whoopee, Bingo, I've won the lottery! Two boards perfectly (not close, perfectly) aligned and flat. A couple of hours later I did much that same thing for the breadboard ends. Purrfect!
Aprons are milled (including the curved underside) and Domi'd ready for the legs. One more day (bar the finishing with shellac, etc) and that piece will be done. Lubberly!
-
1st September 2006, 04:34 PM #59
Domi update - and a question
Originally Posted by Auld Bassoon
One thing I need to do is to cut a series of Domi mortices on a flat panel in two parallel rows a precise distant apart, and equidistant from the panels edges (to locate the apron rails of the server table I'm making). Any suggestions other than using a transverse alignment bar clamped to the workpiece with its own depth stop to the boards edge?
Cheers!
-
1st September 2006, 06:56 PM #60
Bump! Answers please!
Heyup fellahs, I need your opinions before I stuff-up!
Similar Threads
-
Triton Club in Newcastle
By Corunetes in forum CLUB EVENTS - News & InformationReplies: 4Last Post: 9th March 2012, 09:19 PM -
Domino Cutting Action
By warmtone in forum FESTOOL FORUMReplies: 68Last Post: 4th August 2006, 10:12 AM -
Woodworking club in Brisbane?
By Exador in forum ANNOUNCEMENTSReplies: 0Last Post: 14th November 2005, 11:27 AM -
Ipswich Club Qld
By Simomatra in forum CLUB EVENTS - News & InformationReplies: 1Last Post: 15th September 2005, 06:10 PM -
qld / gold coast club listings
By imad in forum WOODWORK - GENERALReplies: 1Last Post: 26th May 2004, 03:06 PM