Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 39
Thread: Chuck back plate
-
12th December 2011, 05:39 PM #1
Chuck back plate
Hi A friend gave me this old back plate ...it is from a old HERON lathe . A outside thread on a tapered bore . It is 6.5" diameter . The tapered bore is 3 and 1/8 down to 3 and 3/4 " Dont know if its much use . I might machine up a tapered hub and press it in, then cut a thread in the hub to use it on the Sheraton ? MIKE Any advice
-
12th December 2011 05:39 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
12th December 2011, 05:45 PM #2Dave J Guest
I would knock the taper off the bore and then press fit a piece if you are going to go that way, as it will hold in by itself then.
Dave
-
12th December 2011, 05:46 PM #3GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 65
- Posts
- 3,566
Would it be easier to bore that plate parallel and then bush it.
If you intend to use it for a backing plate check the PCD of your chuck incase the holes allready in it interfeer.
-
12th December 2011, 05:48 PM #4
Ok
Hi Dave, so you think it is better to remove the taper altogether ? And use a parallel press in spigot ? BTW that taper is over a 1 and 7/8" length . So is there a mathematical genius among us who can work out the angle ? I can turn down the outside to take a 5" chuck .... that would get rid of the ugly holes in the perimeter MIKE
PS what is the most suitable material for the bush/hub Cast iron ?
-
12th December 2011, 06:04 PM #5Dave J Guest
I would take out the taper and press fit a piece into it. Even if you lock a taper piece in with locktight etc, there is always a chance of it coming out latter on down the track.
If you are worried about the press fit piece moving, you can drill and tap on the line between the 2 and run a grub screw into it which will lock it in.
Dave
-
12th December 2011, 06:06 PM #6Dave J Guest
I missed you PS, if you have it around cast iron will be fine, but if you only have steel laying around it will do the job as well.
Dave
-
12th December 2011, 06:12 PM #7
-
12th December 2011, 06:34 PM #8GOLD MEMBER
- Join Date
- Oct 2010
- Location
- melbourne, laverton
- Posts
- 1,469
do you want to sell it
aaron
-
12th December 2011, 10:42 PM #9
too late
Sorry Aaron..I been out in the shed turning it down..its now had the centre bored out ... The outside is harder than the centre ..funny stuff cast iron . The centre bored out easily, but the periphery is so hard ....blunts a HSS tool in no time . I use a tool straight from the grinder , this works better on cast iron than a tool with a honed edge for some reason , beyond me . MIKE
-
12th December 2011, 10:43 PM #10GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 65
- Posts
- 3,566
What speed are you turning the OD.
-
12th December 2011, 10:45 PM #11
-
12th December 2011, 10:48 PM #12GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 65
- Posts
- 3,566
I would suggest to run it no more than 100 RPM if not at its slowest speed,wasnt it around 6".
I would keep the feed down as well.
It wont hurt to put a little positive rake on the tool if you wish.
-
12th December 2011, 10:52 PM #13
-
12th December 2011, 10:54 PM #14GOLD MEMBER
- Join Date
- Oct 2010
- Location
- melbourne, laverton
- Posts
- 1,469
no problem mate not even shore if it was the right one. for me. what sort of lathe do you have?
-
13th December 2011, 02:22 PM #15
Chips
NO not chips that you eat .... the old back plate has changed shape . Took ages to remove all of that cast iron . I reduced the speed as pipeclay suggested ..did the trick .
I think I will shrink on the hub after I have made it up ..What is the best way to do this ... put the plate in a bowl of water and boil it ? MIKE
Similar Threads
-
chuck back plate thread
By tanii51 in forum THE HERCUS AREAReplies: 13Last Post: 10th June 2011, 11:36 PM -
Source of chuck back plates?
By Rebo in forum THE HERCUS AREAReplies: 22Last Post: 6th January 2011, 10:30 PM -
Fitting a 250mm chuck on a face plate, 12x36 lathe
By Dave J in forum METALWORK FORUMReplies: 8Last Post: 7th August 2010, 12:57 PM -
chuck backing plate
By welder in forum THE HERCUS AREAReplies: 5Last Post: 2nd February 2010, 05:26 PM