Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Attaching a Lazy Susan
-
4th June 2009, 01:07 AM #1
Attaching a Lazy Susan
Maybe it's because it's late but I'm working on a Lazy Susan which is a round one rather than the square ones which have plentiful instructions on the web. How do you attach the bottom and top slabs as it seems to me that once the bottom is attached the top screw holes are obscured?
-
4th June 2009 01:07 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
4th June 2009, 01:30 AM #2
It's basically the same process.
Round bearings usually have one "side" larger than the other, with a single large hole in it. This is the "bottom" and you place it in position on the bottom piece, the mark the screw holes and the centre of the "large" hole.
The large hole is drilled out, so that after you screw the bearing to the bottom you can position the assembly onto the top section and fit the screws through the large hole, rotating the bearing to move the hole over each screw.
Easier done than said.
(If you look at the round bearing on this page, you can just barely see the large hole I'm talking about on the inside of the left-hand side.)
- Andy Mc
-
4th June 2009, 08:25 AM #3
Handy link there Skew, thanks for that . Do you know if they sell direct to the public?
To grow old is inevitable.... To grow up is optional
Confidence, the feeling you have before you fully understand the situation.
What could possibly go wrong.
-
4th June 2009, 11:01 AM #4
Thanks, Skew. So you actually have to drill through the wooden base, I didn't think of that as that would ruin the piece but I guess it's only the base.
-
4th June 2009, 01:57 PM #5
I guess if you wanted to retain the option of turning it over you could mount/screw one side and glue the other.
This would eliminate the need for the hole in the base peice of wood.
24 hour Araldite should do the job for you especially if you made a small recess to fit the bearing into also help to locate it centrally.
Cheersregards
David
"Tell him he's dreamin.""How's the serenity" (from "The Castle")
-
4th June 2009, 05:09 PM #6Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
Do you need to screw the base down?
I have a number of lazy susans at home and I just fixed the top to the mechanism and glued some cloth material to the bottom and have them resting on the table. Easy tro move and clean under and they never seem to shift so they are sturdy enough.
Peter.
-
4th June 2009, 06:52 PM #7
Try using with a magnetized philips head screwdriver to attach the screws. I almost gave up on the lazy susans till that hint was given to me.
Cheers, Shirley
-
4th June 2009, 07:18 PM #8
You do with the square ones, too. Unless you're screwing 'em to square bits of wood.
The hole in the base shouldn't be visible from above anyway - unless you're up close and peering into the works of the bearing - 'cos the hole is covered by the mounting plate. It shouldn't "ruin" the look of the base unless you screw up in a BIG way.
Of course, the hole is obvious when you turn it upside-down... but you can always tell a new owner "that's the service hole so you can replace the bearing at a future date, if needed."
- Andy Mc
-
4th June 2009, 09:00 PM #9
I glue a cork floor tile to the bottom of the bearing with contact adhesive, after the bearing is screwed to the top.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
4th June 2009, 11:53 PM #10Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
Similar Threads
-
lazy susan
By hutch in forum WOODWORK - GENERALReplies: 11Last Post: 7th January 2009, 08:44 PM -
Lazy Susan
By John Doyle in forum WOODTURNING - GENERALReplies: 10Last Post: 9th February 2008, 04:13 PM -
Lazy Susan
By BernieP in forum WOODTURNING - GENERALReplies: 12Last Post: 14th April 2007, 10:50 PM -
Lazy Susan
By stu_g18 in forum WOODWORK - GENERALReplies: 11Last Post: 24th May 2005, 08:41 PM -
lazy susan
By Agro in forum TIMBERReplies: 2Last Post: 28th February 2005, 07:39 PM