Thread: Best Type of Sandpaper

rough

Portugese made Indasa stearate abrasives in grits 80 - 400 are my favoured paper backed and Hermes Blue on cloth for all hardwood applications. These abrasives are specially formulated for raw timber.

Originally Posted by ozwinner

rough

I was talking about for wood Al

Cheers

Use Genuine Festo Disks for ROS
Norton half sheet (Green) for rough sanding 80 grit
Had belts made up from some German brand of Sandpaper for AEG Belt Sander

Stay away from the "glass paper" which is typically clear compound on brown backing usually found in cheap shops and some hardware's


I also use the Festool pad for snading between coats, it is like a scotchbrite material, in 600 or 1200 grit, excellent on larger surfaces and saved heaps of time. highly recommended

regards tony

I've tried a few different brands, mostly use Norton these days. It's pretty easily available round here and peforms Ok.

Generally I reckon better value for money comes from the more expensive brands.

I've had good results with sia, 3M and norton.
But I seem to find different grit ranges in the same product vary in staying power.

one brand will br great in the coarse grades another will be better in the mid grades and another will be better in the fine grades.

And differing modes of failure, some go blunt, some the adhesive holding the grains fails & some clog, before others.

I'm talking about good quality stuff that I would consider adequate but differing results and points of failure.

I must pay more attention & do a proper study.
For sure it will also depend on what the job is too.

Without a shadow of doubt the best paper is that bluey/grey stuff with the yellow cloth backing made by "Hermes" Comes in rolls about 200mm wide. Available in lots of grades from '60' to, '800' I think.
Also the 'non-clog' velcro backed 3'' circular ones for the 'Vic Wood' Rotary Sander,(in my humble opinion the best all round sanding method available.)

Hermes from Jim Carroll for me. Always get it fast and $4 a metre is pretty good IMO. Got some today. Ordered it Friday and it arrived today. With the shop at the WWW show all weekend it is fantastic response IMO. Normally arrives within two days.

Dan

SIA and Hermes.

A trick for the newcomers - make it flexible by pulling it across an edge first (the back that is).

And Jim's service is second to none!

http://www.cws.au.com/

Klingspor for me,

But I've not tried or compared the above mentioned ones.

SIA and Hermes are both cloth backed sandpapers that come in widths of 100mm or 150mm. Available in grits 80, 100, 120, 150, 180, 240, 320 and 400 (may be one coarser than 80).
Cost approx $4-$5 per metre (comes in rolls, just tear off the length you need)
You can "flap" , "crack" or whatever the term across the tool rest on the lathe and most of the dust will be removed, giving the paper a longer life.
Available from Carrolls ($4), Carba-Tec ($5).
Good strong sandpaper.
Don

On the subject of the best sandpaper, I would have to agree that Hermes J-flex(the blue stuff on the yellow cloth) is best. Another favorite is their HCAB aluminium oxyde paper. Just a tip amongst ourselves, their factory is in Cheltenham and they throw out truckloads of the stuff as offcuts every day, if you go there and ask nicely, they might let you go through the rubbish bins. But only as a handyman, no commercial quantities! There is also a guy at Caribbean Market selling offcuts of some Hermes product at a discount.
regards workgoose

The best I've ever used came with a drum sander set I bought.
The set contained some short rolls of various grades plus one roll of CZ (cubic zirconium, fake diamond)
I bought some steel bar to change my short quickgrip clamps into long ones.
The steel was rectangular and the clamps needed all the corners rounded over.
I put the largest drum in a drill stand and sanded two 10' lengths of bar for hours until they fitted.
It's like having sandpaper made with diamond dust.
It didn't wear out that I could notice.
I have looked for CZ suppliers but have found none so far so will have to continue using the same piece I have had for years.

(and I'm talking about that ridiculous show on Ch10 - Bright Ideas, or whatever it's called - it's just one continuous advertisement for 3M and a coupla other companies, then they punctuate it with more ad breaks!! AAAAGGGHHH!!!)

Does anyone else get a good run out of that new 3M stuff - Sandblaster, I think they call it. I mainly use such things for guitar refinishing, where obviously the greater deal of work is on predominantly flat areas. Doesn't tend to block as much, and clears pretty easily when it does. Available in most of the popular grades up to about 400 I think, from there I generally go wet&dry anyway for levelling the lacquer before buffing. I find it a lot harder wearing that the Prager AlOx papers, but it's comparatively spendy - guess that depends on how long you can make it last. I haven't come across the Hermes product (with the yellow cloth backing). Might have to look out for it...

Cheerz!