Needs Pictures: 0
Results 1 to 15 of 44
-
15th April 2016, 12:18 AM #1Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
Restoration of my Granddad's Stanley #4.
After trying to decide what my first plane should be, the decision was made for me when my Granddad handed me his trusty Stanley #4.
IMG_20160331_173705 (1).jpgIMG_20160331_185721 (1).jpg
Now, admittedly it's not in great condition, it did have a hard life on the farm, and has been used within an inch of it's life... But never the less, I intend to restore it.
I purchased a donor plane from eBay that had been broken and brazed, the parts I needed were in reasonable condition, I found it cheaper than trying to source it all separately.
planeparts.jpg
So far I've sanded the original knob and replacement tote (sanded it to remove the step introduced when it was repaired).
13010202_10209312661398767_2034619272_o.jpg
The rest has been cleaned and it getting soaked overnight to treat the rust.
IMG_20160414_225158.jpg
Tomorrow I'll take it out, give it a clean, and see what I have to work with
-
15th April 2016 12:18 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th April 2016, 02:52 AM #2
-
15th April 2016, 11:08 AM #3Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
-
15th April 2016, 11:25 AM #4Member
- Join Date
- Aug 2015
- Location
- Canberra, ACT
- Posts
- 51
What product are you using to remove the rust (and how well did it work with the overnight soak)? I picked up a few neglected planes at a garage sale and only semi-successful removing the rust from the working surfaces by hand.
-
15th April 2016, 12:40 PM #5Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
Using Evaporust, will take you a photo when I pull it out. Checked this morning and it looked good. Giving it a deep soak because the Japanning is at about 0%, want it nice and clean and rust free before I paint it.
Edit: Here you go, pretty good result I think.
IMG_20160415_124711.jpgIMG_20160415_125023.jpgIMG_20160415_185632.jpg
There's nary a skerrick of rust to be seen.
Any tips on how to get the rest of the chroming off the lever cap would be appreciatedLast edited by kenour; 15th April 2016 at 02:09 PM. Reason: Adding Photos
-
15th April 2016, 04:17 PM #6Senior Member
- Join Date
- Feb 2012
- Location
- Adelaide
- Posts
- 451
dunno, but some say brake fluid, bleach or oven cleaner will remove it.
edit; otherwise i read some sulphuric acid using some electronic reverse plating methods
cheers
chippy
-
15th April 2016, 08:14 PM #7Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
First coat on the tote and knob.
IMG_20160415_160004.jpg
Brass polished.
IMG_20160415_165050.jpg
Holes and machines surfaces taped up (I hope I got everything!).
IMG_20160415_180511.jpg
Painted.
IMG_20160415_185707.jpg
-
15th April 2016, 08:35 PM #8
nice refurb
but I think there is at least one or two more sharpens in that blade!regards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
15th April 2016, 08:43 PM #9Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
I've got a PM-V11 on the way
The one that came with the donor plane has heaps of meat on it, it's a US made iron on a UK plane, so not its original.
I think the original iron from my Granddad's has been sharpened well past the hardened part right?
I have plans for it anyway, going to attempt to make a custom jigsaw blade from it, 2mm wide with no set to finish plunge saw cuts cleanly.
-
15th April 2016, 10:29 PM #10Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
Tape removed, came out pretty good.
IMG_20160415_202716.jpgIMG_20160415_202818.jpg
Baking on the enamel.
IMG_20160415_203028.jpg
Managed to get rid of the remaining chrome, will probably buff it up at TAFE.
IMG_20160415_210831.jpg
-
15th April 2016, 11:05 PM #11GOLD MEMBER
- Join Date
- Nov 2012
- Location
- SE Melb
- Age
- 65
- Posts
- 1,278
What did you use for your japanning?
-
15th April 2016, 11:32 PM #12Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
First I flew to the Himalayan region and collected some Asphaltum that I ground up into powder, I then... woke up, went to Masters, and got some Killrust Woodstove Enamel Satin Black
It looks the business, and hopefully should be quite durable. I'll let you know if it last's me a lifetime.
-
16th April 2016, 02:35 AM #13Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
Enamel is baked on good and proper, looks pretty close to original.
Feels very good in the hand, nice hard durable feel to it.
IMG_20160416_013200.jpg
-
16th April 2016, 05:55 PM #14Senior Member
- Join Date
- Nov 2012
- Location
- Ballarat
- Posts
- 104
Well there she is.
IMG_2156.jpgIMG_2160.jpg
Will have to shorten the studs to hold the knob and tote more securely, little too much wiggle at the moment, and the knob actually rotates pretty freely. But that's also a tomorrow job.
IMG_2167.jpg
Sole still needs a bit of work, but at the moment, I can't feel my hands, so that can be done later also
-
16th April 2016, 06:47 PM #15
came up well!
regards
Nick
veni, vidi, tornavi
Without wood it's just ...
Similar Threads
-
Stanley/Bailey No4 & 7 restoration
By springwater in forum HAND TOOLS - UNPOWEREDReplies: 76Last Post: 7th January 2016, 07:10 PM -
Stanley 246 (cordless) miter saw- Restoration
By fineboxes in forum HAND TOOLS - UNPOWEREDReplies: 3Last Post: 21st July 2013, 09:51 PM -
Stanley Plane restoration (thanks Major Panic)
By BrettC in forum HAND TOOLS - UNPOWEREDReplies: 7Last Post: 24th February 2013, 06:21 PM -
Stanley 60 Block Plane Restoration
By Burnsy in forum HAND TOOLS - UNPOWEREDReplies: 15Last Post: 6th May 2008, 03:29 PM -
Stanley handyman restoration
By kiwioutdoors in forum HAND TOOLS - UNPOWEREDReplies: 0Last Post: 29th September 2005, 02:00 PM