Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 30 of 34
-
8th September 2017, 09:56 AM #16.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,837
-
8th September 2017 09:56 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th September 2017, 10:29 AM #17Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
-
8th September 2017, 10:34 AM #18Member
- Join Date
- Feb 2012
- Location
- Brisbane, Qld
- Posts
- 95
G'day Clare,
My first lathe was the Carbatec Mini Lathe and it was great. Solid, straight, simple to use. I used it for pens, grinders small bowls, etc. The big cost though is the "accessories". Well worthwhile investing in good accessories because they can be used on just about any lathe, in case you want to upgrade to a larger lathe in the future.
Geoff
-
8th September 2017, 11:02 AM #19
Another option, Clare.
Team up with someone who already has a setup. That way you get a jump start, some guidance and extend your network. You will be more informed after that on what you need for your own setup.
There is a Wood Whispering Women forum somewhere on these woodworking forums. It is not very active, but there might be enough active members to link you up with someone in your area.
As already suggested, non-mens shed woodworking/turning clubs could be another way of linking up with established woodturners.
BTW, almost any lathe with minimal tools will do what you are planning to do.
Sent from my ZTE T84 using TapatalkStay sharp and stay safe!
Neil
-
8th September 2017, 11:41 AM #20
I fully understand what you're saying Fumbler, but I also really appreciate BobL is probably concerned that I might be unaware of the hazards and not safe. This is definitely not the situation in my case as I'm a seasoned sculptor working across a large range of materials and very aware of the various hazards each material/method brings. So I can see it's probably helpful to ask whether someone needs this advice first I guess, so's not to put people off before they've started. However, safety is paramount for us all and the fact someone cares enough to ask if I know how to keep myself safe is heartwarming in this day and age where it seems many folk couldn't give a toss.
Setting all this aside, it's TOTALLY fabulous that so many people are generous with their knowledge and openness to help - and for that I thank you all.
-
8th September 2017, 11:43 AM #21
Thanks so much NeilS!
-
8th September 2017, 11:44 AM #22
Thats great advice, appreciate thanks TinyTool
-
8th September 2017, 05:58 PM #23
NC Archer might still have this little shortbed for sale (go to post no 6)
Hereregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
8th September 2017, 06:56 PM #24Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,472
I belong to a Mens Shed on the north side of Sydney and we have a number of women members - everyone is welcome and encouraged.
-
8th September 2017, 08:23 PM #25GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Sydney
- Posts
- 1,557
-
8th September 2017, 08:29 PM #26
-
8th September 2017, 10:06 PM #27
-
8th September 2017, 11:01 PM #28
I recommend a Woodfast M305 midi, and if you can afford it, the new M305X variable speed model. See https://www.cwsonline.com.au/shop/ca...oodfast-lathes for more details
The Woodfast is a small and light weight lathe but built far more solidly than most of the other small lathe options. Apart from the usual small stuff it also has the ability to even turn a half decent bowl. I have been to nearly all the Turnarounds throughout Australia and the number of Woodfasts out number other brands 4 to 1.Neil____________________________________________Every day presents an opportunity to learn something new
-
9th September 2017, 08:33 PM #29GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,275
I think the Carbatec lathe you have chosen is probably the best bang for your buck, more so when you wish to have a ceiling of $400. This is if you purchase new. Purchasing something second hand, which you have intimated you are willing to do; should mean you can get more bang for your buck, or the lathe you are looking at new, for less.
Things I looked at and still do when considering a lathe, are how low the lowest speed is and what are the speed gradations overall. Closely followed by how easy it is to change the belt for speed changes
When roughing down odd sized and unbalanced timber, you usually need slow speeds, mostly selecting the lowest speed for very out of balance objects. These are usually rough cut logs, which in your case would most likely be tree branches.
Taking your stated request of turning 10cm by 10cm blanks to whatever. Assuming they are squared, you will need to rough cut the sharp edges off first. As these blanks are reasonably balanced the lowest speed of that lathe, which is 300rpm, equates to approximately 1.57 m/s (metres a second) surface speed of your blanks. This is probably a little slow, but as your chosen lathe has 5 speeds from 300 to 3,200, there are only 5 steps, so the next step could be a big one.
Assuming the steps are evenly spaced; they generally are, your steps are probably in 730rpm increments. Meaning your next speed up is 1,030rpm which is 5.4m/s. This speed may be a tad too fast for square blanks, but it would be where I would gently start with a sharp chisel, if possible. You rough the square edges off and reduce the blank to about 85mm. It would probably still have flat surfaces in places.
Once you have blanks around 85mm pick your next speed which is 1,760rpm and your cutting surface is being presented to your chisel at almost 8m/s. This is quite fast, but not a problem with a sharp chisel, in fact about right for many cutting speeds on a lathe. You then reduce your blanks to about 80mm round with a surface speed of about 7.4m/s.
One day I read an article on wood turning and mention was made of the speed of the wood surface that worked well for the author. I did some thinking about the speeds that seemed to work well for me, after some calculations I came to the conclusion that for general work, anything between 5m/s to 8m/s was where I had naturally settled on as about right for me. Obviously as work size decreases as you remove stock, your speed needs to be increased to keep the chisel working as you like.
Most, if not all lathes in the same class I looked at after reading your question and doing a quick search, have minimum speeds of around 500rpm, with some starting at 650rpm. These speeds are alright for small reasonably balanced blanks, but could be a bit iffy with really out of balanced larger rough stock. That said, if you ignore the St Vitas dance of these mini lathes in that initial stage, then fine, but I have been caught out with a mini lathe with too high a low speed with largish (for this size of lathe) very unbalanced blanks.
To put metre per second speeds into place, think of it like this. At 8m/s, your chisel is travelling 8 metres in one second. Picture a room or space known to you that is 8m long, imagine you pushing a chisel that length in 1 second. This is quite a high demand on your chisel, it also shows how technology in the form of steels and machinery has matured to the point that we can discuss and purchase these devices for the cost of a couple of nights in a city hotel. Unbelievably cheap really.
I would suggest if you can stretch your budget, you could consider a Woodfast lathe, the Midi 305 lathe, it has one feature which is to me, its biggest selling point. The ability to change lathe speeds as easy as anything, taking around 15 seconds at the best and 30 seconds at the worst. These changes are done with the operator not needing to change position. One just flips the black left cover leftwards, then move a lever to release the belt (situated in front of the motor). Move the belt to the desired position, then reverse the procedure. You are usually away within 30 seconds.
Wood Lathes
Some thoughts.
Mick.
-
19th September 2017, 11:54 AM #30Member
- Join Date
- Mar 2010
- Location
- Newcastle
- Posts
- 62
What's the ryobi lathe I saw at the bunnies like?
Similar Threads
-
Mini lathe on stand vs mini lathe in bench?
By nz_carver in forum WOODTURNING - GENERALReplies: 20Last Post: 4th February 2013, 08:33 AM -
Lathe purchase
By cookie48 in forum WOODTURNING - GENERALReplies: 14Last Post: 9th December 2010, 10:31 AM -
Where to purchase Mini Orb
By Timmy111 in forum METALWORK FORUMReplies: 4Last Post: 24th February 2009, 08:59 AM -
Help with Lathe purchase........
By HappyHammer in forum WOODTURNING - GENERALReplies: 8Last Post: 19th January 2008, 04:53 AM