Search:

Tag: calc

Search: Search took 0.00 seconds.

  1. 3ph to 3ph VFD

    Started by shedhappens, 15th June 2014 10:25 PM
    4 Pages •
    1 2 3 4
    1.5, 11.5, 120, 1500, 3ph, 4.5%, amateur, belt, bit, calc, calcs, clue, grunt, low, mill, motor, motor/spindle, phase, pulley, range, ratio, rpm, sad, shaft, slip, speed, spindle, splines, variable, vfd 8 Attachment(s)
    • Replies: 51
    • Views: 6,172
    Last Post: 7th August 2014 11:40 PM
    by Chris Parks  Go to last post

    Forum:
    METALWORK FORUM

  2. Speeds and Feeds

    Started by seafurymike, 10th July 2012 05:40 PM
    acknowledgement, assume, calc, cnc, detailed, exe, feeds, found, fraternity, gui, interface, kiwi, lots, material, mdf, metal, speeds, virus, wrote, zone
    • Replies: 5
    • Views: 1,389
    Last Post: 12th July 2012 10:14 AM
    by seafurymike  Go to last post

    Forum:
    CNC Machines

  3. Power supply calc

    Started by wheelinround, 13th July 2011 10:59 PM
    account, amount, calc, calculate, calculator, extreme, monitor, power, running, scanners, software, speakers, supply
    • Replies: 6
    • Views: 1,665
    Last Post: 16th July 2011 11:51 AM
    by Bryanatkinson  Go to last post

    Forum:
    COMPUTERS

  4. What Timber To Use For Gazebo Roof?

    Started by 29687, 26th November 2009 06:09 PM
    approx, brisbane, bucks, buidling, calc, colourbond, confused, contrast, darker, dead, frame, gazebo, hit, kinda, million, nice, octagonal, oiled, pine, posts, questions, roof, stuck, suggestions, supports, timber, weatherboards, weatherproof, weekend, yard
    • Replies: 6
    • Views: 1,660
    Last Post: 28th November 2009 09:22 AM
    by 29687  Go to last post

    Forum:
    WOODWORK - GENERAL

  5. Quick Change Parting Tool Holder

    Started by wannabe, 10th April 2009 09:03 PM
    angle, blade, bought, calc, change, degrees, designing, fine, holder, measure, measurements, mention, mentioned, parting, process, qctp, quick, rake, set, store, tool, type, wondering
    • Replies: 9
    • Views: 2,423
    Last Post: 18th April 2009 10:28 PM
    by Woodlee  Go to last post

    Forum:
    METALWORK FORUM

  6. Surveying / maths question

    Started by ptrott, 30th July 2007 12:16 AM
    3 Pages •
    1 2 3
    angle, assuming, block, bloke, boundary, break, calc, degree, dividing, doh, equal, fairly, front, hand, horizontal, left, line, maths, meet, metres, phill, plan.less, portion, promise, question, rectangle2tsupu, simple, sub-dividing, surveying, top
    • Replies: 31
    • Views: 5,425
    Last Post: 9th September 2007 03:27 PM
    by ian  Go to last post

    Forum:
    GENERAL ODDS N SODS

  7. Anyone help with calc'ing compound mitres?

    Started by Skew ChiDAMN!!, 25th October 2006 06:41 PM
    2 Pages •
    1 2
    angle, bit, boxes, calc, calcing, compound, days, derive, determine, formula, high-school, joints, life, lookup, maths, mitres, paper, pitch, plugging, pyramid, relevant, remember, rolleyes, segments, set, simple, simply, xed], [fingers, [sigh]
    • Replies: 21
    • Views: 3,314
    Last Post: 31st October 2006 09:34 AM
    by czk  Go to last post

    Forum:
    WOODWORK - GENERAL

  8. Is a double layer of r1.5 = r3

    Started by Shannon Nash, 4th August 2006 12:17 AM
    2 Pages •
    1 2
    1.5, 3.5, advertised, advice, aparently, auction, batts, calc, ceiling, double, equivalent, gudday, house, layer, local, lot, r1.5, r15, told, unused, wool
    • Replies: 18
    • Views: 3,851
    Last Post: 16th August 2006 03:13 PM
    by Markw  Go to last post

    Forum:
    PLUMBING, ELECTRICAL, HEATING, COOLING, etc

Results 1 to 8 of 8