Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
-
13th November 2007, 11:07 PM #1Member
- Join Date
- Nov 2006
- Location
- Ireland
- Posts
- 84
stand for jointer and thicknesser
Hi
I’ve just bought a portable thicknesser and would like to build a moveable stand to hold both this and my jointer. I'm not sure how well this would work since the thicknesser in-feed will be close to the ground, however I have seen shop photos where the thicknesser sits under a wing of the table saw.
I’ve found a few pictures of stands on-line but most people seem to use a separate stand for each. I don’t have the space for separate stands ( yes I know I should have originally bought a combined planer/thicknesser but I’ve had the jointer for a while and the thicknesser was a bargain)
Anyone ever built a stand which has a benchtop jointer on top and a benchtop thicknesser on a shelf underneath?
-
13th November 2007 11:07 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
13th November 2007, 11:24 PM #2
I made this mobile stand for my 12" thicknesser and a disk/belt sander, maybe you could do something similar?
-
14th November 2007, 09:57 AM #3
Hi Jim,
I don't have any pictures or plans on file just yet, but, this is the same idea I want to put into use in my shed. I was thinking of building a bench so that the drill press, 6" jointer and compound cutoff saw would sit on top and underneath near the door, build a pullout shelf for the thicknesser so that I can have it near the power and dust extraction (DE), but the planks or boards can be run through from the roller door side throough the thicknesser and out the personal door.
A bit odd, but it would save a lot of space and enable me to keep the thicknesser out of the way when not in use, but most importantly, keep it close to the DE.
Good luck with your setup.
cheers
WendyBox Challenge 2011 - Check out the amazing Boxes!
Twist One - Wooden Hinge/Latch/Catch/Handle
Twist Two - Found Object
Twist Three - Anything Goes
-
14th November 2007, 08:13 PM #4GOLD MEMBER
- Join Date
- Oct 2003
- Location
- Sydney,Australia
- Posts
- 3,157
There have been several plans published of a stand with a flip-over top and the power tolls bolted to opposite sides. You just have a couple of knob/bolts at the corners & a strong pivot in the middle. I have also seen plans for a tool stand with interchangeable bolt down panels for each tool, and storage in a skinny cupboard.
Woodsmith/Shopnotes and Australian Woodsmith have published the flip-top stand - back issues are available. The multi-top stand is in one of Danny Proulx's many DIY books.
-
19th November 2007, 09:38 PM #5Member
- Join Date
- Nov 2006
- Location
- Ireland
- Posts
- 84
Thanks for suggestions
Thanks for the suggestions. I liked Big Shed’s flip over stand but I’m not confident about building a pivot for 70Kg of equipment, don’t think my skills are up to that yet.
I knocked up a quick stand from a couple of sheets of ply and some angle iron, the thicknesser is a lot closer to the floor than I would have liked but at least it’s off my bench.
I had to make the thicknesser shelf wide enough to let the back table stay open, on my model (a Fox F22-560) the rear table won’t fold up if the dust collector is in place.
Similar Threads
-
I fixed the snipe problems in my thicknesser !
By JDarvall in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 38Last Post: 23rd June 2013, 10:56 AM -
Thicknesser or Planer Thicknesser (Jointer)
By Markw in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 5Last Post: 9th November 2006, 01:58 PM -
Thicknesser and Jointer
By boxers in forum WOODWORK - GENERALReplies: 13Last Post: 30th September 2005, 05:39 PM -
Carbatec CTJ 340 thicknesser
By chook in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 1Last Post: 23rd December 2004, 08:26 AM