Search:
Type: Posts; User: Prisky
Search: Search took 0.00 seconds.
-
27th September 2015, 09:59 PM
- Replies
- 16
- Views
- 2,290
I bought the Pec 12 inch combination square off...
I bought the Pec 12 inch combination square off Jim over a year ago and have been really pleased with it.
-
5th May 2015, 11:09 PM
Thread: Elm Dining Table
by Prisky- Replies
- 2
- Views
- 727
Thanks Christos I came to the same conclusion and...
Thanks Christos I came to the same conclusion and have around 6 coats of Ubeauts pre mixed hard blond shellac on the bottom. Looks like it will take awhile but will give the result I want.
-
27th April 2015, 11:03 AM
Thread: Elm Dining Table
by Prisky- Replies
- 2
- Views
- 727
Elm Dining Table
I am making a dining table out of elm and the finishing is more difficult than usual. The elm had started to rot which has left some soft patches the worst of which I have stabilised with casting...
-
12th February 2014, 10:53 PM
- Replies
- 26
- Views
- 5,355
Narex Paring Chisels Flattening
Mine arrived today as well, have flattened them all enough to remove the varnish and mine are also not perfectly flat but close enough to be flattened in a reasonable amount of time (I hope).
I... -
11th July 2012, 11:01 PM
Thread: Coffee Table with Stickley Legs
by Prisky- Replies
- 7
- Views
- 1,464
Coffee Table with Stickley Legs
Just finished a pair of arts and crafts coffee tables. Due to a lack of large enough sections of Oak for the legs I made Stickley legs for the first time. Thought that this would be a better choice...
-
25th June 2012, 09:18 PM
Thread: WIP Recycled Aust Oak King Single Bed
by Prisky- Replies
- 26
- Views
- 4,783
Try casting resin it flows well into holes and...
Try casting resin it flows well into holes and finishes clear.
-
3rd November 2009, 11:50 PM
Thread: Fw floorseal
by Prisky- Replies
- 1
- Views
- 1,409
Floorseal
Could I also ask for some advice. I have a couple or NZ Rimu sofa's my Dad made in the 80's that I have restored and I have put several coats of refined Linseed oil on to darken the timber as Rimu...
-
21st July 2007, 06:02 PM
Thread: garage slab engineering
by Prisky- Replies
- 7
- Views
- 6,645
Shed Slab
As far as I know the slab must be designed for the building to go on it. In general in the industry the shed plans include the slab and this will be easiest way to go. If not take the building plans...
-
18th July 2007, 09:55 PM
Thread: Slats for Queen size bed
by Prisky- Replies
- 14
- Views
- 20,089
Bed Slats
I'm going to try a couple of the Ikea bed slat units for the queen sized bed presently under construction. The one's I am planning to use are the SULTAN LILLÅKER at $100 each. This is planning of...
-
22nd June 2007, 11:01 PM
Thread: Abbey Tournament
by Prisky- Replies
- 2
- Views
- 1,300
Abbey Tournament
In the last 4 that I've been to there hasn't been any wood demo's but it's well worth going to.
-
9th May 2007, 10:29 PM
Thread: Rental houses
by Prisky- Replies
- 10
- Views
- 2,189
We also rent and so I now have all machines on...
We also rent and so I now have all machines on mobile bases and have built a tool cabinet also on wheels. Should be able to wheel most these out to the truck onto the tail gate lift and then into the...
-
10th February 2007, 12:20 AM
Thread: The ongoing saga of the ML392
by Prisky- Replies
- 231
- Views
- 54,969
Bowed Fence
Bob had the same problem and managed to sort by shiming the back of fence in between the bolts and then tightening. So far so good.
-
2nd December 2006, 10:21 PM
Thread: ML-392 specs question
by Prisky- Replies
- 3
- Views
- 1,769
Ml 392
I have the AW106PT which the Carbarec machine and is the also sold by Axminster in the UK. In the manual it has a feed speed of 6m per minute. There are I think some differences to the ML392 which...
-
24th August 2005, 11:01 PM
Thread: Scangrind (wet grinding)
by Prisky- Replies
- 21
- Views
- 10,103
Scangrind
I have the 150 model which I got second hand and find it excellent. At $399 the Scheppach TIG 2000 ex Carbatech might be a better buy.